%
%
%
%
%
%
Detail Steps/Work Items Key Items/References
(1) Remove the left wing. Refer to Section 57-10.
(2) Remove the left fuel tank assembly. Refer to Section 28-11.
(3) Disconnect the electrical cables for the high fuel sensor. At the in-line connector near the high fuel sensor.
(4) Remove the high fuel sensor from the tank.
%
Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003
28-41-00
DA 40 Series
AMM
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
% B. Install the 'High Fuel' Sensor %
Detail Steps/Work Items Key Items/References
(1) Install the high fuel sensor in the fuel tank: S Apply sealant to the thread of the high fuel sensor. S Move the high fuel sensor into position in the fuel tank mount. S Screw the high fuel sensor fully home into the mount. S Tighten the high fuel sensor. Use Loctite 243 or 'seal-lube' or 'fuel-lube'. The arrow must point up.
(2) Connect the electrical cables to the high fuel sensor. At the in-line connector.
(3) Install the left fuel tank assembly. Refer to Section 28-11.
(4) Install the left wing, but do not refuel the airplane. Refer to Section 57-10.
(5) Do a test for the correct operation of the high fuel sensor. Make sure that it switches off the fuel transfer pump when the fuel level in the left tank is high.
(6) Refuel the airplane. Refer to Section 12-10.
(7) Do a check for leaks.
%
Page 204 Doc # 6.02.01 09 Jan 2003 Rev. 4
28-41-00
Fuel System
AMM
% 4. Remove/Install a Fuel Quantity Probe
% Obey the safety precautions for fuel at all times.
% % % A. Remove a Fuel Quantity Probe
%
%
%
%
%
%
%
Detail Steps/Work Items Key Items/References
(1) Remove the wing that has the fuel quantity probe that you will remove, and support the wing on trestles. Refer to Section 57-10.
(2) Remove fuel tank assembly from the wing. Refer to Section 28-11.
(3) Remove the fuel quantity probe from the threaded mounting.
%
Doc # 6.02.01 Page 205
Rev. 4 09 Jan 2003
28-41-00
DA 40 Series
AMM
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
%
% B. Install a Fuel Quantity Probe %
Detail Steps/Work Items Key Items/References
(1) Separate the fuel filler assembly from the fuel tank. Refer to Section 28-11. To gain access to the guide at the outboard end of the fuel tank.
(2) Install the fuel quantity probe into the fuel tank: S Apply sealant to the thread of the fuel quantity probe. S Install a new O-ring seal. S Carefully move the fuel quantity probe into position in the inboard tank. Engage the thread. S Turn the probe clockwise, by hand, until the fuel quantity probe is fully engaged in its mount. S Tighten the fuel quantity probe until the O-ring seals. Use Loctite 243 or 'seal-lube' or 'fuel-lube'. Make sure that the fuel quantity probe goes into the guide at the outboard end of the fuel tank.
(3) Re-connect the fuel filler assembly to the fuel tank. Refer to Section 28-11.
(4) Install fuel tank assembly into wing. Refer to Section 28-11.
(5) Install the wing to the airplane. Refer to Section 57-10.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 3(58)
