曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

(3)  Set the rudder pedals central.  The left pedal must align with the right pedal. Make sure the rudder is in the neutral position shown in the Control Surfaces Adjustment Report for the airplane. 
(4)  Set the rudder pedals to fully left.  The rudder must hit the stops at the rudder pedestal. The rudder position must be the distance to the left shown in the Control Surfaces Adjustment Report for the airplane. (Measured from the neutral position). 
(5)  Set the rudder pedals to fully right.  The rudder must hit the stops at the rudder pedestal. The rudder position must be the distance to the right shown in the Control Surfaces Adjustment Report for the airplane. (Measured from the neutral position). 
(6)  Make sure the left and right rudder pedals are free to move when they are set in all of the adjustable positions. 

27-20-00
Flight Controls
AMM

3. Rudder Control System Adjustments
If you cannot get the correct range of movement of the rudder control system, use this procedure to adjust the system.
A. Equipment
Item  Quantity  Part Number 
Cable tension gauge.  1  Commercial. 
Ruler or deflection gauge.  1  Commercial. 

B. Rudder Adjustment Procedure
Detail Steps/Work Items  Key Items/References 
(1)  Remove these items for access: S The pilots’ seats. S The passenger seat.  Section 25-10. 
(2)  Set both rudder pedals fully forward. 
(3)  Set the rudder pedals central.  Make sure the rudder is in the neutral position. The left pedal must align with the right pedal. 
(4)  If necessary, adjust the length of the cables between the yoke and the rudder lower mounting bracket. S Remove the lock-wire from the turnbuckles. S Adjust the turnbuckles to set the rudder to neutral. S Do a test for correct cable tension. S Tighten the turnbuckles and install the lock-wire.  Refer to Figure 4. Below the passenger seat. Refer to the Adjustment Report. 

Doc # 6.02.01 Page 203
Rev. 4 09 Jan 2003

27-20-00
AMM

DA 40 Series

(5)  Set the rudder pedals to fully left.  The rudder must hit the stops at the rudder pedestal. The rudder position must be the distance to the left shown in the Control Surfaces Adjustment Report. (Measured from the neutral position). 
(6)  If necessary, adjust the rudder stop bolt on the left side of the rudder lower mounting-bracket: S Release the jam-nut on the left stop bolt. S Adjust the stop bolt to give the correct range of movement. S Tighten the jam-nut on the stop bolt.  The rudder position must be the distance to the left shown in the Control Surfaces Adjustment. (Measured from the neutral position). 
(7)  Set the rudder pedals to fully right.  The rudder must hit the stops at the rudder pedestal. The rudder position must be the distance to the right shown in the Control Surfaces Adjustment Report. (Measured from the neutral position). 
(8)  If necessary, adjust the rudder stop bolt on the right side of the rudder lower mounting-bracket: S Release the jam-nut on the right stop bolt. S Adjust the stop bolt to give the correct range of movement. S Tighten the jam-nut on the stop bolt.  The rudder position must be the distance to the right shown in the Control Surfaces Adjustment Report. (Measured from the neutral position). 
(9)  Do a test for the correct range of rudder movement.  Refer to Paragraph 2. 
(10)  Do an inspection of all the controls that you have adjusted. S If necessary for your Airworthiness Authority, do a second inspection of the controls. 
(11)  Install these items: S The pilots’ seats. S The passenger seat.  Refer to Section 25-10. 

27-20-00
Flight Controls
AMM
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：鉆石40飛機維護手冊 DA 40 SERIES AMM 3(9)