国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 飛行資料 >

時間:2010-05-30 00:10來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

but it's a simple slide rule calculation,
based on your flying time against
fuel consumption.
The Dalton Computer
This is a device with a sliding scale
through it, marked with drift angles
and TAS arcs, with a frosted circular
screen on which you can draw the
business end of the triangle of
velocities:
There is a dot in the centre of the
screen, around which is a compass
rose that can be rotated to bring
your heading or track under the
lubber line. All you need to do is
draw in the wind vector to see how
they all relate to each other.
Note: there will be an instruction
book supplied with your computer,
so the instructions given here will
necessarily be brief.
The first thing to do is move the
sliding scale to make your TAS
appear underneath the dot in the
centre of the frosted screen. Then
156 JAR Private Pilot Studies
rotate the screen so the wind
direction lines up under the lubber
line at the top.
Draw in a line vertically downwards
from the centre dot equal to its
speed in knots. Rotate the screen
again until the track is under the
lubber line. The end of the wind line
will point to a drift arc and a TAS
arc, which you just apply to your
track and airspeed to get the missing
bits, namely the true heading to fly
and the resulting groundspeed which
you use for flight planning. Then
apply the magnetic variation and
compass deviation to get the proper
heading to fly.
CR Series
These were invented by Ray Lahr
and marketed by Jeppesen. They are
circular, with no sliding scale, and
are based on trigonometry (they are
easier to work with one hand, but be
aware that, as the angle of drift
increases, there's a small angular
correction to be applied on top).
Below is a picture of how you would
work out the PLOG above.
The cross between the 10 and 20
under the centre of the instrument is
the wind velocity (180/15). Its
position to the right of the main line
going towards TC (True Course)
means the wind is coming from the
right, and the crosswind component
is 2 kts. Looking across from the 20
on the outside scale (bottom right),
you will see that 1.3° is the
correction to be applied to obtain
the heading (the white arrow above
the letters TAS must be opposite the
aircraft's TAS for this to be correct).
The tailwind component is 15 kts,
which should be added to obtain a
groundspeed of 105 kts.
The very small ones have some
functions left out, which are
unimportant to most aircraft anyway,
to pack everything else in, but don't
get one too small, because your eyes
won't see the print so well at night
(see the Human Factors chapter).
Slide Rule
On the other side of both types,
there is a circular slide rule, with the
60 point on the inner scale
conveniently marked to make speed
and time calculations easier:
Flight Planning 157
It can be positioned against fuel
quantity or distance on the outer
scale to read time on the inner scale.
As with any slide rule, you need the
approximate answer to your problem
first, as a protection against gross
error and to give you an idea where
to put the decimal point (if you were
wondering how it works, you are
adding indices, which is also where
logarithms come from, but that is
outside the scope of this book).
The most common problems
concern time and distance. Just
move the inner scale until the 60
point is opposite the TAS or fuel
consumption, for example. Read the
time on the inner scale against
distance on the outer scale, or fuel if
you are checking how much is being
used. In the above picture, the speed
triangle (60) is opposite 120 (knots or
gallons) on the outer scale, which
means it will take 6 minutes to go 12
nautical miles, or 6.5 to use 13
gallons, and so on. Always reduce
hours (and proportions thereof) to
minutes for simplicity.
To multiply normally (e.g. 2 x 4),
place 10 on the inner scale against
one number on the outer scale, and
read the answer on the outer scale
opposite the other, which will be on
the inner scale.
Square roots can be found easily, too
(useful for finding VHF ranges).
Find the number you want the
square root of on the outer scale,
then rotate the inner one until the
number opposite 10 is the same as
the one against your original
number. For example, 400 will have
2 opposite, as well as against 10
 
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:JAR.Private.Pilot.Studies(99)
国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
欧美亚洲另类制服自拍| 国产精品日本一区二区| 亚洲一区免费看| www.欧美精品| 国产美女视频免费| 日本一区二区三区四区五区六区| 国产精品国产对白熟妇| 国产成人精品福利一区二区三区| 国产中文字幕二区| 日韩av三级在线| 一区二区三区在线视频看| 久久久久久久久久久亚洲| 97国产在线播放| 丰满爆乳一区二区三区| 国内精品一区二区三区| 日本三级韩国三级久久| 在线视频不卡一区二区三区| 国产精品成人v| 精品国产一区二区三区在线| 国产精品久久久久久久久久ktv| 国产精品久久久久久超碰| 国产精品三级网站| 久久精品五月婷婷| 久久久com| 国产v综合ⅴ日韩v欧美大片| 国产a级片免费观看| 另类专区欧美制服同性| 国产精品观看在线亚洲人成网| 久久久国产一区二区三区| 国产精品久久久久久久乖乖| 欧美激情精品久久久久久变态| 伊人久久大香线蕉综合75| 伊人久久婷婷色综合98网| 日本久久久网站| 欧美久久综合性欧美| 国产视频精品网| 久久久一本精品99久久精品| 国产a级片网站| 色狠狠av一区二区三区香蕉蜜桃| 国产精品美女999| 欧美激情精品久久久| 一区二区三区我不卡| 日韩视频在线观看国产| 99在线观看视频网站| 久久久久久久成人| 亚洲在线www| 黄页网站大全在线观看| 97成人在线观看视频| 久久久久亚洲精品| 欧美激情精品久久久久| 青青在线视频一区二区三区| 97精品伊人久久久大香线蕉| 久久精品美女视频网站| 国产精品精品国产| 欧洲久久久久久| 国产黑人绿帽在线第一区| 国产精品高潮呻吟视频| 日韩av在线综合| 国产精选一区二区| 在线视频福利一区| 欧洲熟妇精品视频| 国产精品福利久久久| 国产精品久久久久久久久粉嫩av| 色综合91久久精品中文字幕 | 久久久精品在线视频| 日韩a∨精品日韩在线观看| 日韩中文字幕免费视频| 国语自产精品视频在线看| 国产精品入口免费视| 成人精品在线视频| 日韩免费视频在线观看| 91高潮在线观看| 欧美日韩福利在线| 自拍视频一区二区三区| 久久精品无码中文字幕| 国产在线视频在线| 精品福利影视| 欧美精彩一区二区三区| 中文字幕一区二区三区四区五区六区 | 91高跟黑色丝袜呻吟在线观看| 国产成人看片| 国产麻豆日韩| 一女被多男玩喷潮视频| 国产欧美一区二区在线播放| 国产精品美女www| 国产尤物av一区二区三区 | 国产成人综合一区二区三区| 欧美精品自拍视频| 国产精品网站入口| 欧美专区日韩视频| 国产精品-区区久久久狼| 免费毛片网站在线观看| 色综合久久88| 国产成人艳妇aa视频在线| 国内视频一区二区| 欧美一级片中文字幕| 久久精品91久久久久久再现| 国产日韩欧美大片| 日本一区不卡| 一区二区三区国| 久久精品国产免费观看| 国产男人精品视频| 日韩视频在线免费看| 宅男在线精品国产免费观看| 久久偷看各类wc女厕嘘嘘偷窃| 蜜桃麻豆www久久国产精品| 免费不卡在线观看av| 国产精品久久久久久久av电影| 91国产在线播放| 国产乱码精品一区二区三区卡 | 91精品天堂| 欧美日韩精品不卡| 亚洲免费av网| 久久精品电影一区二区| 91精品视频免费观看| 激情深爱综合网| 日本十八禁视频无遮挡| 欧美日本亚洲视频| 色婷婷综合久久久久| 91精品国产综合久久久久久久久| 欧美亚洲激情在线| 日本一区二区不卡高清更新| 在线观看免费黄色片| 久久成人免费视频| 国产精品大全| 久久久久北条麻妃免费看| 久久久久久久久久久av| 久久久久免费网| 久久精品国产精品亚洲| 国产极品jizzhd欧美| 国产精成人品localhost| 加勒比海盗1在线观看免费国语版| 日韩精品国内| 日av中文字幕| 欧美二区三区在线| 国产欧美日韩专区发布| 国产乱子伦精品| 99亚洲精品视频| 91国内精品久久| 久久综合毛片| 国产二区视频在线| 国产超碰91| 日韩在线观看免费| 九九精品在线播放| 亚洲第一精品区| 欧美一级片中文字幕| 欧美一区少妇| 含羞草久久爱69一区| 国产欧美精品一区二区三区介绍 | 久久久999视频| 久久精品久久久久久| 萌白酱国产一区二区| 日韩免费视频在线观看| 国内精品伊人久久| 68精品久久久久久欧美| 日韩亚洲综合在线| 少妇一晚三次一区二区三区| 国产一二三四区在线观看| 91精品在线一区| 国产精品电影在线观看| 中文字幕中文字幕一区三区 | 久久精品国产精品亚洲精品色| 国产精品日韩欧美一区二区| 俺去啦;欧美日韩| 成人做爰www免费看视频网站| 日本久久久久久| 91精品国产综合久久久久久蜜臀| 国产精品网址在线| 日本视频一区二区在线观看| 97福利一区二区| 欧美日韩999| 男女超爽视频免费播放| 久久99精品久久久久子伦| 国产精品久久久久久久久免费| 日本一区二区三区视频免费看 | 久久久久久久久一区二区| 国产精品免费成人| 亚洲精品不卡| 国产精品一区二区三区成人| 久久精品日产第一区二区三区| 一本久道高清无码视频| 欧美日韩三区四区| 深夜福利国产精品| 午夜精品久久久久久久久久久久 | 国产精品久久亚洲| 青青视频在线播放| 久久久久久久91| 日韩区国产区| 久久久久久精| 麻豆成人av| 亚洲一区二区三区色| 国产精品96久久久久久又黄又硬| 亚洲综合视频1区| 国产精品999视频| 日韩国产欧美精品| 国产精品成av人在线视午夜片| 国产日韩一区在线| 亚洲一区二区在线看| 日韩一区二区久久久| 精品视频一区二区在线|