R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 21-52-24-865-052
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
R (1) FOR 10HM4
(a) 1HH, 2HH, 3HH, 4HH, R (2) FOR 11HM4
(a) 21HH, 22HH, 23HH, 24HH.
R **ON A/C 401-499,
Subtask 21-52-24-865-052-A
E. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
R (1) FOR 10HM4
(a) 49HH, 50HH, 51HH, 52HH,
R (2) FOR 11HM4
(a) 53HH, 54HH, 55HH, 56HH.
**ON A/C ALL
Subtask 21-52-24-710-050
F. Test
(1) Do the pre-conditioning through the HP ground connector (Ref. TASK 12-33-21-618-001) or with the APU (Ref. TASK 12-33-21-618-001).
(2) Do a leak check of the heat exchanger unit connections.
NOTE : Minimum leakage is permitted. After the pack operates some____ minutes, the leakage of air will reduce because the seals have their correct operating temperature.
(3) After approx. 15 minutes stop the pre-conditioning (Ref. TASK 12-33-21-618-001) or (Ref. TASK 12-33-21-618-001).
(4) Do the operational test of the cockpit and cabin temperature control (Ref. TASK 21-63-00-710-004).
R 1EFF : ALL 1 21-52-24Page 443 1 1 Aug 01/05 1 1 1CES 1
5. Close-up
________ Subtask 21-52-24-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel (Ref. TASK 53-35-13-400-002)
FOR 10HM4
191KB,
FOR 11HM4
192KB.
(3) Remove the warning notice(s). Subtask 21-52-24-862-050
B. De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
R 1EFF : ALL 1 21-52-24Page 444 1 1 Aug 01/05 1 1 1CES 1
TASK 21-52-24-000-001- 01
Removal of the Heat Exchanger Unit 10HM4 (11HM4) (From the Air Conditioning Pack)
NOTE : The procedure is the same for the heat exchanger unit 10HM4 and 11HM4.____
1. Reason for the Job__________________
Self Explanatory
2. Job Set-up Information______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
21-52-23-000-001 21-52-41-000-001 53-35-13-000-002 CMM 215200 Removal of the Pipe Assembly between the Main Heat Exchanger and the Air Cycle MachineRemoval of the Air Conditioning Pack 10HM (11HM)Removal of the Quick-Release Access Panels from the Belly Fairing Structure
R **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
21-52-24-991-001 Fig. 401
R **ON A/C 151-199, 401-499,
R R 21-52-24-991-001-A Fig. 401A
R 1EFF : ALL 1 21-52-24Page 445 1 1 Aug 01/05 1 1 1CES 1
**ON A/C ALL
3. Job Set-up__________
Subtask 21-52-24-010-052
A. Get Access
(1) Remove the access panel/s (Ref. TASK 53-35-13-000-002).
(a) FOR 10HM4 - 191KB;
(b) FOR 11HM4 - 192KB.
4. Procedure_________
Subtask 21-52-24-020-052
A. Removal of the Heat Exchanger Unit
R **ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
(Ref. Fig. 401/TASK 21-52-24-991-001)
R **ON A/C 151-199, 401-499,
R R (Ref. Fig. 401A/TASK 21-52-24-991-001-A)
**ON A/C ALL
NOTE : Turn the sleeves (16), (88) and (59) when you move them or when____ you remove them. This will help to prevent damage to the internal seals.
(1) Remove the air conditioning pack (Ref. TASK 21-52-41-000-001).
NOTE : Make sure that the air conditioning pack is securely fastened____ in the correct support stand (Ref. CMM 215200) before you remove any of the pack components.
R 1EFF : ALL 1 21-52-24Page 446 1 1 Aug 01/05 1 1 1CES 1 Damage to the individual components could occur if it is not correctly supported.
(2)
Remove the pipe assembly (Ref. TASK 21-52-23-000-001).
(3)
Remove the clamp (9) and the sleeve (8).
(4)
Remove the nut (45), the washer (44), the bonding strap (41) and the screw (42).
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 4(75)
