(9)
 Put the new packing (5) in position on the sensor (4) and put the sensor (4) in position in the condensor (22).

 (10)
 Make sure that the sensor (4) is in the correct position and install the washers (2) and the screws (1).

 (11)
 TORQUE the screws (1) to between 0.2 and 0.25 m.daN (17.69 and 22.12 lbf.in).

 (12)
 Wipe clean the excess COMMON GREASE (Material No. 04-012) from the screws (1) and safety them with annealed stainless-steel lockwire, diameter 0.5 mm (0.0196 in.) MISCELLANEOUS (Material No. 19-009).

 (13)
 Put the new packing (25) in position on the sensor (26) and install the sensor (26) in the condensor (22).

 (14)
 TORQUE the sensor (26) to between 0.5 and 1.0 m.daN (44.24 and 88.49 lbf.in).

R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 21-52-32Page 419 1201-299, 301-399, 1Aug 01/05 1 1 1CES 1

 (15) Wipe clean the excess COMMON GREASE (Material No. 04-012) from the sensor (26) and safety it with annealed stainless-steel lockwire, diameter 0.5 mm (0.0196 in.) MISCELLANEOUS (Material No. 19-009).
R **ON A/C 401-499,
 Subtask 21-52-32-560-050-A
 B. Preparation of the Replacement Component
 (Ref. Fig. 401A/TASK 21-52-32-991-001-A)

 (1)
 Remove and discard the lockwire and remove the sensor (23) from the removed condensor (19).

 (2)
 Remove and discard the packing (22).

 (3)
 Remove and discard the lockwire and remove the screws (1), the washers (2) and the blanking plate (3).

 (4)
 Remove and discard and the packing (4) from the blanking plate (3).

 (5)
 Make sure that the parts retained from the removed component are clean and in the correct condition.

 (6)
 Remove the blanking plugs from the replacement condensor (19).

 (7)
 Clean the component interface and/or the adjacent area.

 (8)
 Apply a small quantity of COMMON GREASE (Material No. 04-012) to the contact faces of the sensor (23) and the screws (1).

 (9)
 Put the packing (4) in position in the groove in the blanking plate (3).

 (10)
 Put the blanking plate (3) in position on the condensor (19) and install the washers (2) and the screws (1).

 (11)
 TORQUE the screws (1) to between 0.2 and 0.25 m.daN (17.69 and 22.12 lbf.in).

 (12)
 Wipe clean the excess COMMON GREASE (Material No. 04-012) from the screws (1) and safety them with annealed stainless-steel lockwire, diameter 0.5 mm (0.0196 in.) MISCELLANEOUS (Material No. 19-009).

 (13)
 Put the new packing (22) in position on the sensor (23) and install the sensor (23) in the condensor (19).

R 1EFF : ALL 1 21-52-32Page 420 1 1 Aug 01/05 1 1 1CES 1

 (14)
 TORQUE the sensor (23) to between 0.5 and 1.0 m.daN (44.24 and 88.49 lbf.in).

 (15)
 Wipe clean the excess COMMON GREASE (Material No. 04-012) from the sensor (23) and safety it with annealed stainless-steel lockwire, diameter 0.5 mm (0.0196 in.) MISCELLANEOUS (Material No. 19-009).

 **ON A/C 001-049, 051-099, 101-105, 151-199, 201-228, 301-302,
 Subtask 21-52-32-420-052
 C. Installation of the Condensor
 NOTE : Turn the sleeves (10) and (14) when you move them or when you
____ install them. This will help to prevent damage to the internal seals or packings. Do an inspection of the sleeve (23) for damage, wear, blisters in the material and seperation of the material from the wire reinforcement. If necessary replace the sleeve (Ref. TASK 21-52-43-000-001) and (Ref. TASK 21-52-43-400-001): for the condensor 10HM2,
 -
sleeve (23).
 for the condensor 11HM2,

 -
sleeve (23).

 (1)
 Make sure that the anti-ice valve sense-lines are in a good condition (Ref. TASK 21-52-00-200-003).

 (2)
 Prepare the attachment components for installation,

 (a)
 Remove the blanking plugs from the disconnected line ends.

 (b)
 Clean the component interface and/or the adjacent area.

 (c)
 Apply a small quantity of:

 -COMMON GREASE (Material No. 04-007)
 or

 -LUBRICANTS (Material No. 06-007) to the new packing (16) and packing (21), and to the new seal
 (9)
 before you install them.

R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 21-52-32Page 421 1201-228, 301-302, 401-499, 1Aug 01/05 1 1 1CES 1 NOTE : The material 04-007 is a molybdenum disulfide powder.

____ Before you can apply it you must first make it into a paste. To do this you must mix the powder with pure water or white spirit.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM AIR CONDITIONING 空調 4(98)