国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 飛行資料 >

時間:2011-03-14 16:05來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

The ECON climb speed is a constant speed/constant Mach schedule optimized to obtain the minimum airplane operating cost. The constant Mach value is set equal to the economy cruise Mach calculated for the cruise altitude entered in the FMC.
For very low cruise altitudes the economy climb speed is increased above normal values to match the economy cruise speed at the entered cruise altitude. For ECON climb, the speed is a function of gross weight (predicted weight at top of climb), predicted top of climb wind, predicted top of climb temperature deviation from ISA, and cost index.

Engine Icing During Climb
Engine icing may form when not expected and may occur when there is no evidence of icing on the windshield or other parts of the airplane. Once ice starts to form, accumulation can build very rapidly. Although one bank of clouds may not cause icing, another bank, which is similar, may cause icing.
Note: The engine anti-icing system should be turned on whenever icing
conditions exist or are anticipated. Failure to follow the recommended
anti-ice procedures can result in engine stall, overtemperature or engine
damage.

Economy Climb
The normal economy climb speed schedule of the FMC minimizes trip cost. It varies with gross weight and is influenced by cost index. The FMC generates a fixed speed schedule as a function of cost index and weight.
Economy climb speed normally exceeds 250 knots for all gross weights. FMC climb speed is limited to 250 knots below 10,000 feet (FAA Airspace), or a lower waypoint speed restriction, if entered. If the use of a higher speed below 10,000 feet is allowed, ECON speed provides additional cost savings.


Economy Climb Schedule - FMC Data Unavailable
737-300 - 737-500
.  
250 knots - Below 10,000 feet
737-300 - 737-500


.  
280 knots/0.74M - Above 10,000 feet
737-600 - 737-900


.  
250 knots/VREF 40 + 70, whichever is higher - Below 10,000 feet
737-600 - 737-900


.  
280 knots/0.76M - Above 10,000 feet

 

Maximum Rate Climb
A maximum rate climb provides both high climb rates and minimum time to cruise altitude. Maximum rate climb can be approximated by using the following: 737-300 - 737-500
.  
flaps up Maneuver Speed + 50 knots until intercepting 0.74M
737-600 - 737-900


.  
flaps up Maneuver Speed + 50 knots until intercepting 0.76M


Note:  The FMC provides maximum rate climb speeds.

Maximum Angle Climb
The FMC provides maximum angle climb speeds. Maximum angle climb speed is normally used for obstacle clearance, minimum crossing altitude or to reach a specified altitude in a minimum distance. It varies with gross weight and provides approximately the same climb gradient as flaps up maneuvering speed.

Engine Inoperative Climb
The engine inoperative climb speed is approximately maximum angle climb speed and varies with gross weight and altitude. After flap retraction and all obstructions are cleared, on the FMC ACT ECON CLB page, select ENG OUT followed by the prompt corresponding to the failed engine. This displays the MOD ENG OUT CLB page (ENG OUT CLB for FMC U10.3 and later) which provides advisory data for an engine out condition.
737-300 - 737-500
Note:  Do not execute the page if VNAV is required for any arrival procedure. If this page is executed, all performance predictions are blanked, VNAV cannot be engaged and though the FMC transitions to ENG OUT CRZ, after a new cruise altitude is inserted, it does not transition to descent. ENG OUT cannot be executed on FMC update 10.0 and beyond.
Copyright . The Boeing Company. See title page for details.
FCT 737 (TM) October 31, 2006

737 Flight Crew Training  Manual
If a thrust loss occurs at other than takeoff thrust, set maximum continuous thrust on the operative engine and adjust the pitch to maintain airspeed.
Note:  Selecting CON on the FMC N1 LIMIT page moves the N1 bug to
maximum continuous thrust until another mode is selected or
automatically engaged. Thrust must be manually set.
The MOD ENG OUT CLB (ENG OUT CLB for FMC 10.3 and later) page displays the N1 for maximum continuous thrust, maximum altitude and the engine out climb speed to cruise altitude, or maximum engine out altitude, whichever is lower. Leave thrust set at maximum continuous thrust until airspeed increases to the commanded value.
Note:  If computed climb speeds are not available, use flaps up maneuvering speed and maximum continuous thrust.


Cruise
This section provides general guidance for the cruise portion of the flight for maximum passenger comfort and economy.

Maximum Altitude
Maximum altitude is the highest altitude at which the airplane can be operated. It is determined by three basic characteristics, which are unique to each airplane model. The FMC predicted maximum altitude is the lowest of:
 
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:737機組訓練手冊 Flight Crew Training Manual FCTM(46)

国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
亚洲三区四区| 国产肉体ⅹxxx137大胆| 亚洲精品一区国产精品| 免费看日b视频| 色偷偷88888欧美精品久久久 | 久久99视频免费| 国自在线精品视频| 国产精品天天av精麻传媒| 日本精品久久久久久久| 国产极品在线视频| 亚洲啪啪av| 91精品久久久久久久久中文字幕| 中文字幕一区二区三区四区五区人 | 91国内精品久久| 亚洲午夜精品一区二区| 国产精品自拍合集| 一区二区在线不卡| 国产精品一 二 三| 欧美激情伊人电影| 国产一区二区三区小说| 国产精品夫妻激情| 国产又黄又爽免费视频| 国产精品久久久久久久久久尿 | 国产精品99免视看9| 国产精品久久久久久av福利| 久久久久久久91| 日韩免费av在线| av动漫在线观看| 亚洲综合在线做性| 97精品视频在线播放| 亚洲18私人小影院| 久久青青草原| 日韩精品一区二区三区丰满| 日日噜噜噜夜夜爽亚洲精品| 欧美在线视频二区| 国产精品日韩一区二区三区| 国产在线精品一区免费香蕉| 国产精品美女视频网站| 国产日韩欧美另类| 亚洲一区免费看| 91精品国产高清久久久久久久久| 欧美一区二区三区精品电影| 久久久久久亚洲| 狠狠色噜噜狠狠色综合久| 精品国产成人av在线免| 国产精品一区二区a| 欧美一级在线播放| 国产精品日韩欧美大师| 成人免费视频97| 日本午夜精品一区二区三区| 精品国模在线视频| 国产日韩欧美夫妻视频在线观看| 在线观看一区二区三区三州| 久久久免费高清电视剧观看| 欧美一级黑人aaaaaaa做受| 久久亚洲成人精品| 国产欧美一区二区三区另类精品| 午夜免费福利小电影| 久久久久久久久久久久久久国产| 黄色免费福利视频| 亚洲视频欧美在线| 久久精品91久久香蕉加勒比| 黄色动漫网站入口| 亚洲一卡二卡三卡| 久久精品国产亚洲| 国产美女主播在线| 日本精品va在线观看| 国产精品美女无圣光视频| 产国精品偷在线| 欧美性一区二区三区| 国产精品福利网站| 国产精品99久久久久久久久| 日韩一区在线视频| 国产精品免费看久久久香蕉| 国模精品系列视频| 亚洲欧美日韩精品久久久| 久久久国产精品免费| 国产欧美综合一区| 日本久久久久亚洲中字幕| 国产精品情侣自拍| 国产精品88a∨| 国产一区在线观| 久久久久久com| 色av吧综合网| 日本高清视频精品| 久久6精品影院| 色青青草原桃花久久综合| 国产精品揄拍500视频| 欧美牲交a欧美牲交| 亚洲欧美日产图| 国产精品九九久久久久久久| 久久99精品久久久水蜜桃| 成人国产精品久久久久久亚洲| 欧美在线免费视频| 亚洲aⅴ日韩av电影在线观看| 国产精品久久77777| 国产不卡一区二区三区在线观看| 国产一区二区在线播放| 奇米影视亚洲狠狠色| 亚洲色精品三区二区一区| 国产精品高潮在线| 国产成人生活片| 国产盗摄xxxx视频xxx69| 成人h视频在线观看| 国产在线高清精品| 极品美女扒开粉嫩小泬| 日韩精品一区二区三区四| 亚洲不卡中文字幕| 亚洲一区免费网站| 欧美精品videos性欧美| 久久天天躁狠狠躁夜夜躁2014| 日韩一中文字幕| 久久一区二区三区av| 国产狼人综合免费视频| 韩国一区二区av| 青青青国产精品一区二区| 欧美一区二区大胆人体摄影专业网站| 中文字幕一区二区中文字幕| 精品国产aⅴ麻豆| 国产精品久久国产精品| 国产精品丝袜高跟| 日韩中文字幕久久| 久久久久久久久影视| 久久久999视频| 69久久夜色精品国产69乱青草| 国产精品夜间视频香蕉| 国产欧亚日韩视频| 国产在线精品一区二区三区 | 国产日韩在线亚洲字幕中文| 男人添女人下部视频免费| 日韩欧美黄色大片| 日本免费成人网| 日韩av成人在线观看| 性亚洲最疯狂xxxx高清| 午夜精品久久久久久久无码| 亚洲一区美女| 亚洲一区二区三区加勒比| 午夜免费日韩视频| 日本久久久精品视频| 亚洲精品日韩av| 亚洲xxxx视频| 视频一区在线免费观看| 色欲色香天天天综合网www| 欧美一区二区三区电影在线观看| 欧美一区二区福利| 欧美综合在线观看| 欧美第一黄网| 国产日韩精品在线播放| 国产精品永久入口久久久| 91免费精品视频| 久久人91精品久久久久久不卡| 久久美女福利视频| 日韩在线视频网| 国产精品入口免费视频一 | 日本不卡高字幕在线2019| 日韩免费黄色av| 欧美成人一区二区在线观看| 精品日韩美女| 豆国产97在线| 久久亚洲精品无码va白人极品| 久久www免费人成精品| 日韩视频永久免费观看| 久久国产精品偷| 亚洲 欧美 综合 另类 中字| 热草久综合在线| 精品一区二区三区自拍图片区| 国产人妻777人伦精品hd| 97精品视频在线| 99爱精品视频| 久久久久久久香蕉| 欧美成年人视频| 亚洲a级在线播放观看| 欧美这里只有精品| 国产男人精品视频| 国产传媒一区| 国产精品久久久久7777| 午夜精品美女久久久久av福利 | 青青青国产精品一区二区| 精品视频免费观看| 7777精品伊久久久大香线蕉语言| 久久久久久欧美精品色一二三四| 国产精品高清在线观看| 亚洲乱码中文字幕久久孕妇黑人| 日韩国产欧美精品| 国产免费一区二区三区| 久久爱av电影| 欧美激情一级二级| 欧美亚洲国产视频小说| aaa级精品久久久国产片| 久久久精品久久久| 一本一生久久a久久精品综合蜜| 任我爽在线视频精品一| www黄色日本| 国产精品免费福利| 日本一本a高清免费不卡| 国产一区二区丝袜| 久久久久人妻精品一区三寸| 中文精品无码中文字幕无码专区 | 国产极品美女高潮无套久久久| 久久天天躁狠狠躁夜夜躁2014|