国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽

  • 熱門標簽

當前位置: 主頁 > 航空資料 > 飛行資料 >

時間:2011-03-14 16:05來源:藍天飛行翻譯 作者:admin
曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

VDPs are indicated on some non-ILS approach charts by a "V" symbol. The distance to the runway is shown below the “V” symbol. If no VDP is given, the crew can determine the point where to begin the visual descent by determining the height above the airport (HAA) of the MDA(H) and use 300 feet per NM distance to the runway.
In the following example, an MDA(H) of 550 feet MSL with a 100 feet touchdown zone elevation results in a HAA of 450 feet. At 300 feet per NM, the point to begin the visual descent is 1 . NM distance from the runway.

Most VDPs are between 1 and 2 NM from the runway. The following table provides more examples.
HAA (feet)  300  400  450  500  600  700 
VDP Distance, NM  1.0  1.3  1.5  1.7  2.0  2.3 

Note:  If flying a VNAV path approach and the airplane remains on the published path, then the VDP is automatically complied with when the airplane arrives at the DA(H) or MDA(H). It is not necessary to determine the point to begin the visual descent for VNAV path approaches for this reason.
When flying an instrument approach using V/S, if the pilot adjusts the altitude range arc to approximately the VDP distance in front of the runway by varying the vertical speed, the airplane will remain close to or on the proper path for typical non-ILS approaches.
Copyright . The Boeing Company. See title page for details.
5.60  FCT 737 (TM) October 31, 2006


Missed Approach - Non-ILS
Refer to Go-Around and Missed Approach - All Approaches, this chapter.
If a missed approach is needed atany time while circling, make an initial climbing turn toward the landing runway and intercept the missed approach course.
MCP altitude / MDA(H)
Select ALT HOLD

. (as needed)

 

Set missed approach altitude
.

Select HDG SEL .
Configuration at MDA(H)
Gear down
.


Gear up (1 engine)
.

Flaps 15
.

Flaps 10 (1 engine)
.

Arm speedbrake
.

Before turning base or initiating the turn to base
Gear down (1 engine)
.


Landing flaps
.

Do the Landing checklist
.

Intercepting landing profile
Disengage autopilot and
. autothrottle

Approach and Missed Approach 737 Flight Crew Training  Manual

Circling Approach
Copyright . The Boeing Company. See title page for details.
5.62 FCT 737 (TM) October 31, 2006

Circling Approach - General
The circling approach should be flown with landing gear down, flaps 15, and at flaps 15 maneuvering speed. Use the weather minima associated with the anticipated circling speed. Maintain MCP altitude or MDA(H) using ALT HOLD mode and use HDG SEL for the maneuvering portion of the circling approach. If circling from an ILS approach, fly the ILS in VOR/LOC and VNAV or V/S modes.
Note:  If the MDA(H) does not end in “00”, set the MCP altitude to the nearest 100 feet above the MDA(H) and circle at MCP altitude.
Use of the APP mode for descent to a circling approach is not recommended for several reasons:
.  
the AFDS does not level off at MCP altitude

.  
exiting the APP mode requires initiating a go-around or disconnecting the
autopilot and turning off the flight directors.

 

Note:  If VNAV ALT (as installed) is allowed to remain as the pitch mode during
the circling maneuver with a higher altitude, (e.g., missed approach
altitude), set in the MCP, the VNAV ALT pitch mode will revert to CWS P.
When in altitude hold at MCP altitude or MDA(H) and before commencing the circling maneuver, set the missed approach altitude.
Before turning base or when initiating the turn to base leg, select landing flaps and begin decelerating to the approach speed plus wind correction. To avoid overshooting final approach course, adjust the turn to final to initially aim at the inside edge of the runway threshold. Timely speed reduction also reduces turning radius to the runway. Do the Landing checklist. Do not descend below MDA(H) until intercepting the visual profile to the landing runway.
Leaving MDA(H), disengage the autopilot and autothrottle. After intercepting the visual profile, cycle both F/D to OFF, then to ON. This eliminates unwanted commands for both pilots and allows F/D guidance in the event of a go-around. Complete the landing.
Note:  If a go-around is selected with either flight director switch in the OFF
position, the flight director pitch or roll command bar on the corresponding
side will disappear when the first pitch or roll mode is selected or engaged.

Obstruction Clearance
Obstruction clearance areas during the circling approach are depicted in the following figure. Distances are determined by airplane approach category. Adjust airplane heading and timing so that the airplane ground track does not exceed the obstruction clearance distance from the runway at any time during the circling approach.
 
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址:737機組訓練手冊 Flight Crew Training Manual FCTM(81)

国产男女无遮挡_日本在线播放一区_国产精品黄页免费高清在线观看_国产精品爽爽爽
欧洲精品在线一区| 久久一区二区三区av| 99在线国产| 亚洲国产精品综合| 91九色国产ts另类人妖| 日日摸天天爽天天爽视频| 国产精品96久久久久久| 日本精品va在线观看| 久久精品影视伊人网| 蜜臀久久99精品久久久酒店新书| 国产精品国色综合久久| 国产精品一区二区久久| 无码人妻丰满熟妇区96| 色偷偷9999www| 国产一区二区三区免费不卡| 亚洲在线一区二区| 久久久久久久久久久久久久久久久久av | 国产精品久久久久久久久久小说 | 在线一区高清| 国产成a人亚洲精v品在线观看| 日韩精品在线视频免费观看| 国产精品毛片va一区二区三区| 国产乱子夫妻xx黑人xyx真爽| 亚洲欧美久久234| 久久精品成人欧美大片| 国产日韩精品在线观看| 欧美一区二区视频在线| 国产精品日韩一区| av无码精品一区二区三区| 人妻熟女一二三区夜夜爱 | 视频在线精品一区| 国产精品美女呻吟| 91精品天堂| 欧美福利精品| 在线观看一区欧美| 色视频www在线播放国产成人| 国产欧美中文字幕| 色一情一乱一乱一区91| 国产精品国产三级国产aⅴ浪潮| www.com毛片| 激情综合网俺也去| 婷婷四房综合激情五月| 欧美xxxx18性欧美| 久久久久久久久久久人体| 国产欧美日本在线| 人偷久久久久久久偷女厕| 中文字幕一区二区三区乱码| 精品久久久av| 91国产在线免费观看| 欧美二区三区| 亚洲一区二区三区毛片| 国产精品久久久久久久久免费 | 欧美亚州一区二区三区| 亚洲一区二区三区在线视频| 国产精品久久久久久久久久直播 | 亚洲砖区区免费| 国产精品国产一区二区| 国产高清精品一区二区三区| 国产欧美丝袜| 欧美成人一区二区在线观看| 亚洲巨乳在线观看| 精品国产一区二区三| 国产精品偷伦免费视频观看的| 91国产在线精品| 国产乱码一区| 麻豆精品视频| 欧美精品自拍视频| 日本精品www| 日本一区高清在线视频| 亚洲人体一区| 一级日韩一区在线观看| 久久伊人精品天天| 久久久久久九九九| 久久综合一区二区三区| 超碰在线97av| 国产精品在线看| 精品无码一区二区三区爱欲 | caoporn国产精品免费公开| 国产日产欧美a一级在线| 欧美日韩免费精品| 日本午夜人人精品| 天天综合中文字幕| 亚洲影院色在线观看免费| 九九综合九九综合| 久久综合色88| 国产精品美女av| 国产精品久久视频| 国产精品嫩草影院一区二区| 一区二区三区三区在线| 国产伦精品一区二区三区四区视频| 日本a级片电影一区二区| 一区二区三区四区久久| 国产精品久久久久久婷婷天堂| 久久久av水蜜桃| 俄罗斯精品一区二区| 欧美不卡三区| 高清不卡一区二区三区| 国产精品一区二区三区毛片淫片| 国产青春久久久国产毛片| 国产人妻人伦精品| 国产日韩在线精品av| 国产一区高清视频| 国产欧美一区二区三区久久人妖 | 亚洲一区三区在线观看| 亚洲一区二区三| 亚洲精品国产精品国自产| 亚洲va久久久噜噜噜久久天堂| 亚洲精品免费av| 日韩中文字幕亚洲精品欧美| 欧美一区2区三区4区公司二百| 亚洲最新在线| 水蜜桃亚洲一二三四在线 | 97免费视频在线播放| 午夜免费久久久久| 亚洲制服欧美久久| 亚洲图色在线| 亚洲一区不卡在线| 中文字幕日本最新乱码视频| 欧美激情中文网| 中文字幕久久一区| 在线视频精品一区| 久久av.com| 久久在精品线影院精品国产| 欧美一区亚洲一区| 春日野结衣av| 欧美一区深夜视频| 国产免费黄视频| 69av视频在线播放| 久久久黄色av| 中文网丁香综合网| 日韩美女在线观看| 国产亚洲精品自在久久| 91九色在线视频| 久久久999国产精品| 精品国产一区二区三区免费| 五月天在线免费视频| 青青青国产在线观看| 国产一区二区三区色淫影院| 国产精品10p综合二区| 久久精品视频亚洲| 国产精品免费观看在线| 成人444kkkk在线观看| 中文字幕一区综合| 三级三级久久三级久久18| 日本欧美视频在线观看| 欧美在线日韩精品| 免费看国产精品一二区视频| 国产日韩欧美精品在线观看| 97久久精品在线| 久久国产精品 国产精品| 欧洲日本亚洲国产区| 任我爽在线视频精品一| 国产精品自拍合集| 久久精品久久久久久国产 免费| 一卡二卡三卡视频| 欧美 日韩 国产 在线观看| 99在线精品免费视频| 国产精品日韩久久久久| 懂色av一区二区三区在线播放| 成人精品一区二区三区电影免费| 国产日韩欧美亚洲一区| 91精品国产乱码久久久久久蜜臀| 国产成人av影视| 国产精品国产三级国产专区53| 亚洲天堂第一区| 欧美在线一区二区三区四区| 国产亚洲第一区| 99国精产品一二二线| 亚洲国产精品毛片| 日本不卡免费新一二三区| 爱福利视频一区二区| 国产精品久久久久免费| 日韩精品另类天天更新| 97久久国产精品| 欧美成人免费在线观看| 青青草成人免费在线视频| 国产福利视频一区二区| 亚洲一区久久久| 丰满爆乳一区二区三区| 久久国产精品久久久| 欧美国产综合在线| 久草热久草热线频97精品| 一道本在线观看视频| 国产视频一区二区三区在线播放| 按摩亚洲人久久| 日本免费高清不卡| 久久久无码中文字幕久...| 中文字幕一区二区三区四区五区人| 国产一区二区三区高清| 精品国产一区二区三区四区在线观看| 日韩av一区二区三区在线观看| 97欧洲一区二区精品免费| 久久久久久国产精品| 国产裸体舞一区二区三区| 久久伊人精品天天| 国精产品一区一区三区视频| 国产精品免费一区二区三区都可以 | 欧美国产视频在线观看| 国产成人看片| 欧美中文字幕第一页|