(b)
 Install the cover (1) and push it to get correct attachment of the velcro tapes.

 4. Close-up
________ Subtask 25-11-42-942-050
 A. Make sure that the work area is clean and clear of tool(s) and other items.
 EFF : ALL

25-11-42Page 406

 SEAT - FOURTH OCCUPANT (13MM) - INSPECTION/CHECK
________________________________________________
 TASK 25-11-42-200-001
 1. Reason for the Job
 Inspection/Check of the Fourth Occupant Seat __________________ Detailed Inspection of seat structure and attachment
 2. Job Set-up Information______________________ Not Applicable _________
3. Procedure
 Subtask 25-11-42-210-050
 A. Inspection Check of the Fourth Occupant Seat
 (1)
 Make sure that the upholstery of the seat is not worn or damaged.

 (2)
 Make sure that the velcro pads on the cushions of the back of the seat and the headrest are in the correct condition.

 (3)
 Make sure that all the bolts that attach the seat have no corrosion and are correctly installed.

 (4)
 Make sure that the seat is not loose and that the fittings are in the correct condition.

 (5)
 Make sure that the control cable of the seat belt is not worn.

 (6)
 Make sure that the seat belt and the buckle are in the correct condition.

 EFF : ALL

25-11-42Page 601

 SEAT - CAPTAIN/FIRST OFFICER (3MS,4MS) - REMOVAL/INSTALLATION
_____________________________________________________________
 TASK 25-11-51-000-001
 Removal of the Captain/First Officer Seat (3MS, 4MS)
 1.
 Reason for the Job

__________________
 Self Explanatory

 2.
 Job Set-up Information

______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific blanking cap
 No specific circuit breaker(s) safety clip(s)
 No specific access platform 1.60 m (5 ft. 3 in.)

R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)

 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
25-11-51-991-001-A Fig. 401
 25-11-51-991-002-A Fig. 402

 EFF : ALL

25-11-51Page 401

 3. Job Set-up
__________ Subtask 25-11-51-865-053
 A. Open, safety and tag this(these) circuit breaker(s):
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 3MS
 122VU COCKPIT SEATS/SEAT CTL/CAPT 1MS1 U11
 122VU LIGHTING/FLOOD/CAPT/SIDE 5LE Z05 FOR 4MS
 122VU COCKPIT SEATS/SEAT CTL/F/O 1MS2 U14
 122VU LIGHTING/FLOOD/F/O/SIDE 4LE Z06
 Subtask 25-11-51-010-050
 B. Get access to the Avionics Compartment
 (1)
 Put an access platform near the access door 811 of the avionics compartment.

 (2)
 Open the access door 811.

 4. Procedure
_________
 (Ref. Fig. 401/TASK 25-11-51-991-001-A, 402/TASK 25-11-51-991-002-A) Subtask 25-11-51-020-051
 A. Removal of the Seat
 (1)
 In the avionics compartment, disconnect the electrical connector (5).

 (2)
 Put a blanking cap on the electrical connectors (5) and (6). NOTE : It is necessary to remove the armrest on the side stick side

____ to enable passage of the seat in the cockpit.

 (3)
 Remove the bolts (7). Remove the armrest (1) from the seat. NOTE : Make sure the seat is in the stowed position before you remove

____
 the bolts (7).

 (4)
 In the cockpit, remove the bolts (3) and the washers (4) from the seat base (2).

 EFF : ALL

25-11-51Page 402
May 01/05
R
 CES

R R  Captain Seat Figure 401/TASK 25-11-51-991-001-A
 EFF :  ALL  25-11-51 Page 403 Nov 01/00
 CES 

R R  First Officer Seat Figure 402/TASK 25-11-51-991-002-A
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備1(103)