-
(Ref. TASK 25-54-11-000-001)
-
(Ref. TASK 25-54-12-000-001)
-
(Ref. TASK 25-54-12-000-002)
-
(Ref. TASK 25-54-12-000-003)
(b)
AFT cargo compartment:
-
(Ref. TASK 25-55-11-000-001)
-
(Ref. TASK 25-55-11-000-002)
-
(Ref. TASK 25-55-11-000-003)
-
(Ref. TASK 25-55-12-000-001)
-
(Ref. TASK 25-55-12-000-002)
-(Ref. TASK 25-55-12-000-003) Subtask 25-00-00-210-065
D. Limits
(1)
Make sure the linings are clean and in the correct condition.
(a) If necessary do the repair (Ref. TASK 25-00-00-340-004).
(2)
Select the related procedure "A" or "B", see para. 4. of this task. (Ref. Fig. 835/TASK 25-00-00-991-011)
4. Procedure
_________ Subtask 25-00-00-340-101
A. Procedure "A"
-Installation of a Protection Patch (S-Glass Layer Assembly D2557651900200) with Double Sided Adhesive Layer
(Ref. Fig. 836/TASK 25-00-00-991-049) NOTE : The weight of the lining will increase by 790 g (27.86 oz) per 1
____
m2 (10.76 ft.2).
NOTE : Do not use the patch to overlap another protection patch.
____
(1)
Cut a protection patch S-Glass layer assembly D2557651900200 to the applicable dimensions.
(2)
Transfer/drill all holes from the lining before you install the protection patch.
(3)
Clean the mating surface.
Repair Procedure Identification Chart
Figure 835/TASK 25-00-00-991-011
EFF : ALL 25-00-00 Page A881
Aug 01/05
CES
CC Honeycomb Linings, Protection Patch
Figure 836/TASK 25-00-00-991-049
EFF : ALL 25-00-00 Page A882
Aug 01/05
CES
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
(a) Clean the mating surface of the lining with CLEANING AGENTS (Material No. 11-010) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
(4) Install the protection patch.
WARNING : MAKE SURE THAT THE PROTECTION PATCH DOES NOT TOUCH:
_______
-
THE FASTENERS AND THE WASHERS
-
THE FLANGES AND H-PROFILES
OF THE DECOMPRESSION PANEL.
IF THE PATCH TOUCHES THESE ITEMS, IT IS POSSIBLE THAT THE
DECOMPRESSION PANEL WILL NOT OPERATE CORRECTLY.
(a)
At a corner of the protection patch, lift a small piece of the protective backing.
(b)
Carefully put the protection patch in position on the view side of the lining.
(c)
Make sure that all holes are aligned and that there is a
sufficient clearance to the adjacent components (e.g.
decompression panel).
NOTE : A later adjustment is not possible.
____
(d)
Carefully hold the protection patch, remove the remaining protective backing and put the the protection patch onto the lining.
(e)
Push the protection patch onto lining with a ROLLER - RUBBER.
NOTE : Move the roller from the center to the edges to avoid or
____
remove air bubbles.
(f) Make sure that all interface holes and cutouts are in the correct position so that you can install the panel and/or the related equipment.
Subtask 25-00-00-340-102
B. Procedure "B"
-Installation of a Protection Patch (S-Glass Layer D2557651900000) with 2 Component Adhesive
(Ref. Fig. 836/TASK 25-00-00-991-049)
NOTE : The weight of the lining will increase by 690 g (24.33 oz) per 1
____
m2 (10.76 ft.2).
NOTE : Do not use the patch to overlap another protection patch.
____
(1)
Cut a protection patch S-Glass layer D2557651900000 to the applicable dimensions.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM EQUIPMENT/FURNISHINGS 設備1(90)
