(4)
Disconnect the suction hose/tube (10) from the union (15) on the pump (35).
NOTE : Use a second wrench to hold the union (15) on the pump (35)
____
when you loosen the hose/tube coupling nut.
(5)
Remove the union (15) and the packing (55) from the suction port of the pump (35) and discard the packing (55).
(6)
Disconnect the pressure hose/tube (5) from the union/reducer (65) and the pump (35).
NOTE : Use a second wrench to hold the union/reducer (65) on the pump
____
(35) when you loosen the hose/tube coupling nut.
(7)
Remove the union/reducer (65) and the packing (60) from the pressure port on the pump (35) and discard the packing (60).
(8)
Remove the pump (35) as follows:
(a)
Loosen the four mount nuts (50).
(b)
Turn the pump (35) in a clockwise direction so that the nut goes through the large part of the hole in the pump flange.
(c)
Move the pump (35) forward and it from the engine.
(9)
Remove the gasket (45) from the mount pad and discard the gasket
(45).
(10)
Remove the packing (40) from the pump input splined-shaft and discard the packing (40).
(11)
Put protective covers on the end of the hose/tube assemblies, the unions, the unions/reducers, the pump and the electrical connector.
(12)
Put blanking plugs on the open end of the pump and on the gearbox mount pad.
1EFF : ALL 1 29-11-51Page 405 1 1 Feb 01/05R 1 1 1CES 1
TASK 29-11-51-400-041
Installation of the Green Engine Pump (1030GK)
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
WARNING : DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.
CAUTION : DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC
_______ FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice(s)
No specific container 5 l (1.3208 USgal)
No specific container 8 l (2.1133 USgal)
No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00
to 10.00 m.daN)
No specific Torque Wrench : range 180.00 to 1800.00 lbf.in
(2.00 to 20.00 m.daN)
B.
Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00)
Material No. 03-002 GB DEF-STAN 91-101
LUBRICATING OIL TURBINE ENGINE SYNT BASE
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
30 packing
40 packing
R 45 gasket 55 packing 60 packing
D. Referenced Information29-11-51 02A-04029-11-51 01 -140 29-11-51 02A-02029-11-51 02A-06029-11-51 02A-090
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the
External Power
24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power
29-10-00-710-001 Operational Check of Hydraulic Fire Shut Off Valves
and Associated Indicating System
29-11-00-710-001 Operational Test of the Green Hydraulic System
29-14-00-614-001 Depressurization of the Hydraulic Reservoirs
29-14-00-614-002 Pressurization of the Hydraulic Reservoirs through
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓2(121)
