Hydraulic Pressure Hose/Tube Assembly
Figure 404/TASK 29-11-49-991-907
1EFF : ALL 1 29-11-49 Page 417
1 1 Feb 01/98
1 1
1CES 1
NOTE : Use a second wrench to hold the wrenching flats of the
____ tee-fitting when you loosen the coupling nut on the tube.
(6)
Remove the bolt (5), the washer (10) and the clamp (15) that attach the pressure hose/tube (20) to the lower bracket.
(7)
Remove the bolt (25), the washer (30) and the nut (35) from the band of the center mount clamp (40).
(8)
Open the band of the clamp (40) and remove the pressure hose/tube
(20) from the insert. Put the band on the insert and install the bolt (25), the washer (30) and the nut (35).
(9)
Remove the pressure hose/tube (20) from the engine.
(10) Put protective covers on the tee-fitting and the ends of the pressure hose/tube (20), the union on the hydraulic pump, and the fitting on the fluid disconnect panel.
1EFF : ALL 1 29-11-49Page 418 1 1 Feb 01/03R 1 1 1CES 1
TASK 29-11-49-400-002
Installation of the Hydraulic Pressure Hose/Tube Assembly
WARNING : OBEY THE HYDRAULIC SAFETY PROCEDURES.
_______
WARNING : DO NOT TOUCH THE HYDRAULIC SYSTEM COMPONENTS FOR A SHORT TIME AFTER
_______ THE ENGINE IS SHUTDOWN. THE ENGINE COMPONENTS STAY HOT FOR SOME TIME AND CAN CAUSE INJURY.
CAUTION : DO NOT LET HYDRAULIC FLUID FALL ON THE ENGINE. UNWANTED HYDRAULIC
_______ FLUID MUST BE REMOVED IMMEDIATELY WITH A CLEAN LINT FREE CLOTH. THE FLUID CAN CAUSE DAMAGE TO THE SURFACE PROTECTION AND TO SOME PARTS.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific warning notice(s)
No specific container 5 l (1.3208 USgal)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00
to 150.00 lbf.ft) FOR FIN 1000EM1 No specific access platform 0.8 m (2 ft. 7 in.)
B.
Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-12-29-611-001 Fill the Hydraulic Fluid Reservoir with a Hand Pump 12-12-29-611-002 Fill the Hydraulic Fluid Reservoir with a Hydraulic
Service Cart 29-11-00-710-001 Operational Test of the Green Hydraulic System 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs 29-23-00-864-001 Depressurize the Green and Yellow Hydraulic Systems
after Operation of the PTU
29-11-49-991-906 Fig. 403
29-11-49-991-907 Fig. 404
FOR FIN 1000EM1
R 71-13-00-010-040 Opening of the Fan Cowl Doors R 71-13-00-410-040 Closing of the Fan Cowl Doors
3. Job Set-up
__________
Subtask 29-11-49-860-066
A. Aircraft Maintenance Configuration
(1)
Make sure that the Green hydraulic system is depressurized (Ref. TASK 29-23-00-864-001).
(2)
Make sure that the Green hydraulic reservoir is depressurized (Ref. TASK 29-14-00-614-001).
(3)
Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Green hydraulic system: - on the ground service panel 197CB.
(4)
Make sure that the warning notice(s) is (are) in position on the access door 195BB to tell persons not to pressurize the Green hydraulic reservoir.
Subtask 29-11-49-941-066
B. Safety Precautions
(1)
On the center pedestal, on the ENG panel 115VU:
-make sure that warning notice(s) is (are) in position to tell persons not to start the engine.
(2)
Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3)
Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Green hydraulic system:
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓2(99)
