(2)
Install blanking caps on the electrical connector and on the electrical receptacle on the reservoir (16).
(3)
Remove the nut (14), the bolt (10) and the washer (13) and disconnect the bonding jumpers (11),(12) from the reservoir.
(4)
Loosen the union nut (20) and disconnect the air pipe (19) from the reservoir (16).
(5)
Loosen the union nut (2) and disconnect the air pipe (1) from the reducer (24).
(6)
Loosen the union nut (8) and disconnect the seal drain pipe (9) from the pressure relief valve (7).
(7)
Loosen the union nut (36) and disconnect the suction pipe (35) from the elbow (37).
(8)
Loosen the union nut (42) and disconnect the return pipe (43) from the reservoir (16).
(9)
Loosen the union nut (44) and disconnect the suction pipe (45) from the reservoir (16).
Reservoir of the Green Hydraulic System (Sheet 2)
Figure 402/TASK 29-11-41-991-002
R 1EFF : 001-003, 051-054, 1 29-11-41Page 407 1 1 May 01/05 1 1 1CES 1
Reservoir of the Green Hydraulic System (Sheet 2) Figure 402A/TASK 29-11-41-991-002-A
R 1EFF : 004-049, 055-099, 101-149, 151-199, 1 29-11-41Page 408 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(10)
Loosen and remove the two nuts (50).
(11)
Remove the two bolts (46) and the washers (47).
(12)
Remove the pipe clamp halves (48),(49).
(13)
Remove and discard the lockwire from the reservoir strap bolts (39).
(14)
Hold the reservoir (16) and loosen the two reservoir strap bolts (39).
(15)
Disconnect the ends of the reservoir straps (38) and remove the reservoir (16) from the aircraft.
(16)
Install blanking plugs in all open pipe ends and unions and in the reservoir ports.
1EFF : ALL 1 29-11-41Page 409 1 1 Nov 01/98R 1 1 1CES 1
TASK 29-11-41-400-001
Installation of the Green Hydraulic Reservoir
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
No specific container
No specific warning notices
No specific access platform 2.6 m (8 ft. 6 in.)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00
to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft)
B.
Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific lockwire, corrosion-resistant steel dia 0.8 mm
(0.032 in.)
Material No. 02-003 F NSA 307110 TYPE 4
HYDRAULIC FLUID (PHOSPHATE ESTER BASE)
(Ref. 20-31-00)
Material No. 05-004 USA MIL-L-25567 TYPE I
OXYGEN LEAK DETECTOR (Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R 5 O-ring
R 5 O-ring
6 O-ring
R 18 O-ring
R 18 O-ring
R 22 O-ring
R 22 O-ring
R 23 O-ring
R 23 O-ring
D. Referenced Information
29-11-41 01 -200 29-11-41 01A-20029-14-03 10 -020 29-11-41 01 -200 29-11-41 01A-200 29-11-41 01 -200 29-11-41 01A-200 29-11-41 01 -190 29-11-41 01A-190
-------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓2(59)
