(10)
 Loosen the pipe end-fitting (26) and disconnect the tee-connector

 (25) from the union (27).

 (11)
 Hold the manifold (35) and remove the nuts (11) and the washers (12).

 (12)
 Remove the manifold (35) together with the spacer plate (13).

 (13)
 Install blanking plugs on the open connections of the manifold and on the disconnected pipe ends.

R **ON A/C 059-099, 102-149, 151-199, 201-299, 301-399, 401-499,
 Subtask 29-11-15-020-050-A
 A. Removal of the Manifold CAUTION : USE A SECOND WRENCH TO APPLY COUNTERTORQUE TO THE UNION WHEN
_______ YOU DISCONNECT/CONNECT HYDRAULIC LINES ON UNIONS. IF YOU USE THE SECOND WRENCH, YOU WILL NOT LOOSEN OR TIGHTEN THE UNION TOO MUCH.
 (1)
 Disconnect the electrical connectors (29),(36).

 (2)
 Put blanking caps on the disconnected electrical connectors.

 (3)
 Remove the nut (53), the bolt (49) and the washer (50) and disconnect the bonding jumper (51) from the structural attachment (52).

 (4)
 Loosen the pipe end-fittings (8),(40) and remove the pipe (7).

 (5)
 Loosen the pipe end-fittings (33),(42) and remove the pipe (32).

 (6)
 Loosen the pipe end-fitting (2) and disconnect the pipe (1) from the union (3).

 (7)
 Loosen the pipe end-fittings (18),(54) and remove the pipe (17).

 (8)
 Loosen the pipe end-fitting (22) and disconnect the pipe (21) from
 the union (23).

 (9)
 Loosen the pipe end-fitting (26) and disconnect the tee-connector

 (25) from the union (27).
 (10)
 Hold the manifold (35) and remove the nuts (11) and the washers (12).

 (11)
 Remove the manifold (35) together with the spacer plate (13).

 (12)
 Install blanking plugs on the open connections of the manifold and on the disconnected pipe ends.

R 1EFF : 059-099, 102-149, 151-199, 201-299, 1 29-11-15Page 407 1301-399, 401-499, 1Aug 01/05 1 1 1CES 1 **ON A/C ALL

 TASK 29-11-15-400-001
 Installation of the Power Transfer Unit (PTU) Manifold of the Green Hydraulic System
 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plugs
 No specific container
 No specific plastic bags
 No specific plastic or wooden scraper
 No specific warning notices
 No specific access platform 3.0 m (9 ft. 10 in.)

R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
 (2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
 (8.00
 to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN

 (15.00 to 150.00 lbf.ft)

 B.
 Consumable Materials

 -------------------------------------------------------------------------------
REFERENCE  DESIGNATION
 -------------------------------------------------------------------------------
No specific  lockwire, corrosion-resistant steel dia 0.8 mm
 (0.032 in.)
R Material No. 02-003 F NSA 307110 TYPE 4 HYDRAULIC FLUID (PHOSPHATE ESTER BASE) (Ref. 20-31-00) Material No. 09-013 USA MIL-PRF-81733 TYPE I CLASS A CORROSION INHIBITING BRUSH CONSISTENCY (Ref. 20-31-00) Material No. 09-018 USA AMS 3267/3 CORROSION INHIBITING LOW ADHESION SEALANT (Ref. 20-31-00)
 Material No. 16-003  F ASNB70720
 COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)

 C. Expendable Parts
 -------------------------------------------------------------------------------
FIG.ITEM |DESIGNATION  |IPC-CSN
 -------------------------------------------------------------------------------
4 back-up rings 29-11-15 02A-170 4 back-up rings 29-11-15 02A-170A 5 O-ring 29-11-15 02A-180 6 O-ring 29-11-15 02A-160 6 O-ring 29-11-15 02A-160A 15 back-up rings 29-11-15 02 -030 15 back-up rings 29-11-15 02A-030 31 back-up rings 29-11-15 02 -120 31 back-up rings 29-11-15 02A-120 34 O-ring 29-11-15 02 -150 34 O-ring 29-11-15 02A-200 38 O-rings 29-11-15 02 -020 38 O-rings 29-11-15 02A-020 60 O-rings 29-11-15 02 -020 60 O-rings 29-11-15 02A-020 61 back-up rings 29-11-15 02 -040 61 back-up rings 29-11-15 02A-040 62 square section seals 29-11-15 02 -050 62 square section seals 29-11-15 02A-050 63 O-rings 29-11-15 02 -110 63 O-rings 29-11-15 02A-110
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM HYDRAULIC POWER 液壓2(23)