TASK 34-43-00-440-001 Reactivation of the TCAS
1. Reason for the Job
__________________
Refer to the MMEL TASK: 34-43-01
NAVIGATION
TCAS
(FAA Only)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power TSM 34PB101 (for corrective action)
3. Job Set-up
__________ Subtask 34-43-00-860-069
A. Aircraft Maintenance Configuration
(1) Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002).
4. Procedure
_________ Subtask 34-43-00-440-050
A. Do the Trouble Shooting of the TCAS (Ref. TSM 34PB101).
1EFF : ALL 1 34-43-00Page 403 1 1 Feb 01/98 1 1 1CES 1
5. Close-up
________ Subtask 34-43-00-860-070
A. Put the aircraft back to its initial configuration.
(1)
De-energize the aircraft electrical circuits
(Ref. TASK 24-41-00-862-002).
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 34-43-00Page 404 1 1 Feb 01/98 1 1 1CES 1
TRAFFIC COLLISION AVOIDANCE SYSTEM (TCAS) - ADJUSTMENT/TEST
___________________________________________________________ TASK 34-43-00-740-001 BITE Test of the TCAS
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
24-41-00-861-002 Energize the Aircraft Electrical Circuits from the External Power 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied from the External Power 31-32-00-860-010 Procedure to Get Access to the SYSTEM REPORT/TEST NAV
Page 31-60-00-860-001 EIS Start Procedure 31-60-00-860-002 EIS Stop Procedure 34-10-00-860-004 IR Alignment Procedure
3. Job Set-up
__________ Subtask 34-43-00-860-050
A. Aircraft Maintenance Configuration
(1)
Energize the aircraft electrical circuits
(Ref. TASK 24-41-00-861-002).
(2)
Do the EIS start procedure (PFDs and NDs only) (Ref. TASK 31-60-00-860-001).
(3)
Do the IR alignment procedure (Ref. TASK 34-10-00-860-004).
(4)
On the EFIS control sections of the FCU:
-
set the mode selector switches to ROSE
-
set the scale selector switches to 10.
(5)
On the center pedestal, if the ATC/TCAS control unit has the ALTITUDE REPORTING function , set the ALT RPTG (or ALT RPT) switch to ON.
1EFF : ALL 1 34-43-00Page 501 1 1 Aug 01/05R 1 1 1CES 1
(6) Do the procedure to get access to the SYSTEM REPORT/TEST NAV page on one MCDU (Ref. TASK 31-32-00-860-010): - push the NEXT PAGE function key (two times) until the TCAS menu page comes into view.
Subtask 34-43-00-865-050
B. Make sure that this(these) circuit breaker(s) is(are) closed:
R -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU COM NAV/ATC/1 5SH1 G11
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
R 121VU COM NAV/TCAS 4SG K10
R **ON A/C ALL
R 121VU COM NAV/ATC/2 5SH2 K07
4. Procedure_________
**ON A/C 001-049, 101-105, 151-199,
Subtask 34-43-00-740-050
A. BITE Test of the TCAS
NOTE : During the test, obey the instructions shown on the MCDU used.____
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
On the MCDU:
-push the line key adjacent to the TEST indication.
- on the MCDU, the subsequent TEST pagewith instructions comes into view. - on the CAPT and F/O NDs, these symbols come into view:
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航3(140)
