1EFF : ALL 1 34-42-00Page 509 1 1 Aug 01/02R 1 1 1CES 1

 Subtask 34-42-00-865-057
 B. Make sure that this(these) circuit breaker(s) is(are) closed:
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU COM NAV/RAD ALTM/2 1SA2 K12 121VU COM NAV/RAD ALTM/1 1SA1 K11
 Subtask 34-42-00-865-058
 C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU EIS/GPWS/115VAC  3WZ P07
 4. Procedure
_________
 Subtask 34-42-00-730-050
 A. System Test NOTE : This note is for RA1 test, for RA2 test you must open the circuit breaker 1SA1. If you do this test in descent, you can make sure that the auto call out announcements are correct. To do this, set a small SLOPE. To decrease the total test time, increase the speed of the altitude change. To do this, adjust SLOPE to a larger value or set a lower STOP ALT.
 -------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:  On the MCDU:
 -push the line key adjacent to  - the LRRA1 (LRRA2) RAMP TEST page
 the RA1 (RA2) indication. Then comes into view.
 push the line key adjacent to
 the RAMP TEST indication.

 -for each value, enter the  On the MCDU, these values come into number in the scratchpad and view: push the related line key:
R 1EFF : ALL 1 34-42-00Page 510 1 1 Aug 01/02 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
* START ALT : 0 ft.  * + 0 ft.
 * STOP ALT : 2500 ft.  * + 2500 ft.
 * SLOPE : 25 ft/s. (Ref. NOTE). * 25 ft/s.
 - push the line key adjacent to the TRIGGER indication.  On the CAPT and F/O PFDs, the ramp teststarts. The speed scale moves up to 2500 ft. and stops after approximately 1 minute 40 seconds.
 On the MCDU, the RAMP TEST PROCESSING message comes into view. When the altitude increases:
 - on the CAPT and F/O PFDs: . when the altitude is between 0 and
 160 ft., the horizon line moves down. The elevation scale comes into view.
 . when the altitude is between 0 and
 570 ft., the red ribbon adjacent to the altitude scale moves down and
 then it goes out of view.
 - push the line key adjacent to the RETURN indication.  On the MCDU:- the LRRA1 (LRRA2) page comes into view.
 **ON A/C 001-004,
 Post SB 34-1171 For A/C 001-004,
 Subtask 34-42-00-730-050-A
 A. System Test

 NOTE : This note is for RA1 test, for RA2 test you must open the circuit breaker 1SA1. If you do this test in descent, you can make sure that the auto call out announcements are correct. To do this, set a small SLOPE. To decrease the total test time, increase the speed of the altitude change. To do this, adjust SLOPE to a larger value or set a lower STOP ALT.
 1EFF : ALL 1 34-42-00Page 511 1 1 Aug 01/02R 1 1 1CES 1

 -------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
1. On the MCDU:
-
push the line key adjacent to the RA1 (RA2) indication. Then push the line key adjacent to the RAMP TEST indication.

-
push the line key adjacent to the RETURN indication.

 **ON A/C ALL
 5. Close-up
________ Subtask 34-42-00-860-053On the MCDU:
-
the RA1 (RA2) RAMP TEST page comesinto view with these indications:TWO SUCCESSIVES RAMPS:RAMP1: 500-50FT (10FT/S) RAMP2: 50-0FT (3FT/S) MAKE SURE THAT AUTO CALL OUT ALTITUDES ARE CORRECTLY ANNOUNCED

 On the CAPT (F/O) PFD:

 -
the ramp test starts. The speed scale moves down from 500 to 0 ft. and stops after approximately 1 minute.

 -when the altitude is between 500 and 0 ft., the red ribbon adjacent to the altitude scale moves up.
 On the MCDU:
 -at the end of the test, the TEST OK page comes into view.
-the RA1 (RA2) page comes into view.
 A. Put the aircraft back to its initial configuration.
 (1)
 On the center pedestral, on the MCDU, push the line key adjacent to the RETURN indication until the CFDS page comes into view.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM NAVIGATION 導航3(85)