(b)
Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in position in front of the cargo door.
(6)
For 30WV and 32WV:
(a)
Open the cargo door (Ref. TASK 52-30-00-860-001) to get access to the door sill area.
(b)
Put an ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the cargo door.
1EFF : ALL 1 52-71-00Page 604 1 1 Feb 01/05 1 1 1CES 1 (7) For 19WV1, 19WV2, 21WV1 and 21WV2:
(a)
Put an ACCESS PLATFORM 5M (16 FT)- ADJUSTABLE in position in front of the FWD passenger/crew door 831 or 841 or in front of the AFT passenger/crew door 832 or 842.
(b)
Open the FWD or AFT passenger/crew door (Ref. TASK 52-10-00-010-001).
(c)
Pull down the cover flap from the emergency exit hatch and remove it to get access to the target of the proximity switch.
NOTE : When you remove more than one cover flap, make a mark on
____ each one to make the installation easier.
(8) For 23WV, 36WV, 38WV and 40WV:
(a)
Put an ACCESS PLATFORM 3M (10 FT)- ADJUSTABLE in front the avionics compartment door 811 or 812 or 822 or 824.
(b)
Open the avionics compartment door :
For 36WN
811
For 23WV
812
For 38WV
822
For 40WV
824. (Ref. TASK 52-41-00-010-002)
Subtask 52-71-00-865-079
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------FOR 11WV1, 11WV2, 13WV1, 13WV2, 15WV1, 15WV2, 17WV1, 17WV2
121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10 121VU EIS/SDAC1 AND 2/DOOR/DET/PAX 48WV P05
FOR 25WV
C/B NOT APPLICABLE
FOR 28WV, 30WV, 32WV, 34WV 49VU L/G/LGCIU/SYS1/NORM 1GA C09
1EFF : ALL 1 52-71-00Page 605 1 1 Feb 01/05 1 1 1CES 1 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
122VU DOORS/CARGO 1MJ T12
FOR 19WV1, 19WV2, 21WV1, 21WV2 121VU EIS/SLIDES/ARM AND WARN/FLT 15WN P11 121VU EIS/SLIDES/ARM AND WARN/GND 13WN P10
FOR 23WV, 36WV, 38WV, 40WV 49VU AIR COND/AVNCS VENT/CTL 6HQ D06 121VU EIS/SDAC1 AND 2/DOOR/DET/AVNCS 46WV P02
Subtask 52-71-00-020-057
D. Removal of the Component
(1)
Remove the lining panel:
FOR 11WV1
221JW (Ref. TASK 25-23-45-000-005).
FOR 11WV2
222JW (Ref. TASK 25-23-45-000-002).
FOR 13WV1
831EZ, 831CZ (Ref. TASK 25-23-46-000-001).
FOR 13WV2
841EZ, 841CZ (Ref. TASK 25-23-46-000-001).
FOR 15WV1
261UW (Ref. TASK 25-23-45-000-003).
FOR 15WV2
262UW (Ref. TASK 25-23-45-000-004).
FOR 17WV1
832EZ 832CZ (Ref. TASK 25-23-46-000-002).
FOR 17WV2
842EZ 842CZ (Ref. TASK 25-23-46-000-002).
FOR 30WV, 32WV
825AR and/or 826AR, 826BR and 826CR
(2)
Remove the insulation blanket, if necessary.
1EFF : ALL 1 52-71-00Page 606 1 1 Feb 01/05 1 1 1CES 1 Subtask 52-71-00-110-050
E. Preparation of the Inspection Area
WARNING : USE SOLVENTS/CLEANING AGENTS, SEALANTS AND OTHER SPECIAL
_______ MATERIALS ONLY WITH A GOOD SUPPLY OF AIR. OBEY THE MANUFACTURERS INSTRUCTIONS. PUT ON PROTECTIVE CLOTHING. DO NOT GET THEM IN YOUR MOUTH. DO NOT SMOKE. DO NOT BREATHE THE GAS. THESE MATERIALS ARE POISONOUS, FLAMMABLE AND SKIN IRRITANT. GET MEDICAL HELP IF YOUR SKIN OR EYES BECOME IRRITATED.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
(1)
Clean the metal parts with CLEANING AGENTS (Material No. 11-010) and a lint-free cotton cloth MISCELLANEOUS (Material No. 19-003).
(2)
Loosen dust and unwanted material from the electrical connector with CLEANING AGENTS (Material No. 11-010) and a soft brush.
(3)
Dry the connector with a clean low pressure air jet.
4. Procedure
_________
Subtask 52-71-00-200-050
A. Inspection of the Proximity Switches
(1)
Examine the sensor for damage and distortion, specially the pins of the electrical connector. Make sure that there are no shocks on the detection face.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM DOORS 艙門8(32)
