(b)
Loosen the jam nuts (37) to disassemble the link assy (40).
(c)
Turn the connection rod (38) counterclockwise to remove it from the both fork ends (35),(39).
(d)
Remove and discard the tab washers (36) from the connection rod (38).
(e)
Install new tab washers (36) on the connection rod (38).
(f)
Put the connection rod (38) to between the lower (35) and the top fork end (39) and turn it clockwise to assemble the link assy (40).
(g)
Turn the connection rod (38) until the clearance between the sensor (23) and the target (31) is correct.
(h)
Examine the link assy (40) to make sure that the connection rod
(38) is installed correctly in the both fork ends (35),(39).
(i)
Tighten the jam nuts (37) and safety them with the tab washers (36).
R 1EFF : ALL 1 52-71-12Page 425 1 1 May 01/05 1 1 1CES 1 Subtask 52-71-12-865-055
D. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1MJ, 1GA
Subtask 52-71-12-720-051
E. Operational Test
(1)
Do the EIS start procedure (Upper ECAM DU and lower ECAM DU only) (Ref. TASK 31-60-00-860-001).
(2)
Do this test to make sure that the proximity switch operates correctly.
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1. On the FWD and/or AFT cargo On the lower display unit of the ECAM door(s): system:
-pull the locking handle away - the symbol of the applicable cargo
from the cargo door. door and the message CARGO are shown in amber.
-push the locking handle into - the symbol for the applicable cargo the recess of the handle flap. door changes to green.
-the related message CARGO goes off.
(3)
Do the EIS stop procedure (Ref. TASK 31-60-00-860-002).
(4)
If required, adjust the applicable proximity switch (Ref. TASK 52-71-00-820-003).
R 1EFF : ALL 1 52-71-12Page 426 1 1 May 01/05 1 1 1CES 1
5. Close-up
________
**ON A/C 001-049, 051-099, 101-149, 201-299, 301-399,
Subtask 52-71-12-410-052
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel(s) 825AR and/or 826AR.
(3)
Remove the access platform(s).
(4)
Make sure that the applicable cargo door is correctly closed (Ref. TASK 52-30-00-860-002).
R **ON A/C 151-199, 401-499,
Subtask 52-71-12-410-052-A
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel(s) 825AR and /or 826AR, 826BR and 826CR.
(3)
Remove the access platform(s).
(4)
Make sure that the applicable cargo door is correctly closed (Ref. TASK 52-30-00-860-002).
1EFF : ALL 1 52-71-12Page 427 1 1 Aug 01/05 1 1 1CES 1R **ON A/C 001-049, 051-099, 101-105,
TASK 52-71-12-000-003
Removal of the Proximity Switch 50WV
1. Reason for the Job
__________________
To replace the proximity sensor and/or the proximity target installed at the latch spigot bracket of the Bulk door frame.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific access platform 2.30 m (7 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
52-30-00-860-006 Open the Bulk Cargo-Compartment Door
52-71-12-991-003 Fig. 403
3. Job Set-up
__________
Subtask 52-71-12-865-056
A. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION
-------------------------------------------------------------------------------
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機(jī)維護(hù)手冊 AMM DOORS 艙門8(43)
