B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 72-23-00-991-305 Fig. 405
 3. Job Set-up
__________ Subtask 72-23-00-941-075
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 F 『 EEFF : ALL E Page 43272-23-00
 E E May 01/05 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 Subtask 72-23-00-010-086
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Put the access platform in position.

 Subtask 72-23-00-040-063
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 Subtask 72-23-00-010-096
 D. Open the thrust reverser cowl doors: (Ref. TASK 78-36-00-010-040)
 FOR 1000EM1
 451AL, 452AR
 FOR 1000EM2
 461AL, 462AR

 4. Procedure
_________
 (Ref. Fig. 405/TASK 72-23-00-991-305)
 Subtask 72-23-00-020-063
 A. Removal of the fan duct panels.
 CAUTION : DURING REMOVAL OF FAN DUCT PANELS, DO NOT FULLY REMOVE CAPTIVE
_______ SCREWS FROM PANEL. THESE SCREWS ARE HELD IN PLACE BY A RETAINING BUSHING ON THE BACK SIDE OF THE PANELS WHICH MAY FALL INTO THE VBV CAVITY IF SCREWS ARE FULLY REMOVED. AFTER REMOVAL OF EACH PANEL, IT MUST BE VERIFIED THAT BUSHINGS ARE STILL WITH PANEL AND NOT IN VBV CAVITY.
 F 『 EEFF : ALL E Page 43372-23-00
 E E May 01/05 ERE
ECES E F 『 E C F M E E E E 56-5B E

 Fan Duct Panel
 Figure 405/TASK 72-23-00-991-305

 F 『 EEFF : ALL E Page 43472-23-00
 E E May 01/05 ERE
ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 (1) Loosen the captive screws (150), and remove the panel (160).

 (2) Unscrew and remove the retaining bushings (170) from the screws (150).

 (3) Remove the washers (180) from the screws (150).

 F 『 EEFF : ALL E Page 43572-23-00
 E E May 01/05 ERE
ECES E TASK 72-23-00-400-027 Installation of the Fan Duct Panels

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific access platform 1 m (3 ft. 3 in.) No specific Torque Wrench : range 36.00 to 220.00 lbf.in
 (0.40 to 2.60 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No.  CP1039 
R  Material No.  CP1041 
R 
R  Material No.  CP2011 
R 
Material No.  CP2101 
R  Material No.  CP2559 
R 
R  Material No.  CP2560 
R 
R  Material No.  CP2566 
R 
R  Material No.  CP2584 
R 
R  Material No.  CP2656 
R 

*
 acetone (Ref. 70-30-00)
*
isopropyl alcohol (Ref. 70-30-00)
*
stoddard solvent (Ref. 70-30-00)
USA MIL-T-5544
 graphite grease (Ref. 70-30-00)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 1(127)