INTENTIONALLY BLANK

 F 『R E E Page 62372-23-00
 E E May 01/05 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

R  Fan Rotor Blades - Local Distortions Figure 606/TASK 72-23-00-991-326- 12 (SHEET 1)
 F EEFF : E E ECES  ALL  『E 72-23-00EEE Page 624 May 01/05

R  Fan Rotor Blades - Local Distortions Figure 606/TASK 72-23-00-991-326- 22 (SHEET 2)
 F EEFF : E E ECES  ALL  『E 72-23-00EEE Page 625 May 01/05

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
B. Nicks, dents and scratches on contour surfaces of root area, Area A and Area C.
C. Nicks, dents and scratches on leading and trailing edges of root area, Area A and Area C.
 D. Nicks, dents and scratches on contour surfaces of areas B and D
E. Nicks, dents and scratches on leading and trailing edges in areas B and D
F. Localized distortion on leading and No limited quantity if no deeper than 0.003 in.
F  『
 EEFF :  ALL  E 
E  E
R  E  E 
ECES  E

(0.08 mm) after removal of high metal
No limited quantity if not deeper than 0.006 in. (0.15 mm)
No limited quantity if not deeper than 0.015 in. (0.38 mm), with 0.40 in. (10.16 mm) max length for scratches after removal of high metal
No limited quantity in AREA D if not deeper than 0.04 in. (1.02 mm), and/or no limitedquantity in area B if not deeper than 0.03 in.
 (0.76 mm), with 0.40 in.
 (10.16 mm) max length for scratches after removal of high metal
Not serviceable.
(Ref. Fig. 605/TASK 72-23-00-991-325)
Replace blade (Ref. TASK72-21-00-000-007) and(Ref. TASK 72-21-00-400-007) or blend the defects(Ref. TASK 72-21-00-320-003) if damage is within the blending limit of figure (Ref. Fig. 605/TASK 72-23-00-991-325)
Do blending procedure(Ref. TASK 72-21-00-320-003)
Do blending procedure(Ref. TASK 72-21-00-320-003)
Do blending procedure(Ref. TASK 72-21-00-320-003)
Replace blade (Ref. TASK72-21-00-000-007) and(Ref. TASK 72-21-00-400-

72-23-00Page 626
Aug 01/05

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
trailing edges of root area, Areas A and C
 G. Leading and trailing edges, distortion in Areas B and D
H. Blade tip for:
 (1) Leading-edge tip curl
Two areas may be distorted not deeper than 0.34 in. (8.64 mm) out of contour provided there are no sharp corners and the minimum length L is six times the depth of the distortion
Tip curl must not extend more than dimension X1 =
0.5 in. (12.7 mm) across
the blade tip and not
 more than dimension X =

 0.5 in. (12.7 mm) along
 the leading edge.
 Maximum deflection from
 original contour is
 dimension Y = 0.25 in.

 (6.35 mm) .
 A maximum of 6 blades
 can have tip curl up to
 dimension X1 = 1.3 in.

 (33.02 mm) across the
 blade tip and dimension
 X = 2 in. (50.8 mm)
 along the leading edge
 with maximum deflection
 from original contour
 dimension Y = 0.6 in.

 (15.24 mm) . No more
 than 3 blades to these
 increased limits can be
 adjacent. In all cases,
 deflection tip angle
 must not be more than 60

007).

Do a spot fluorescentpenetrant inspection(Ref. TASK 70-51-00-230-002)
Replace pair of blades(Ref. TASK 72-21-00-300-002).
 F 『 EEFF : ALL E Page 62772-23-00
 E E Aug 01/05 ERE
ECES E

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
degree from original airfoil.
 (2) Trailing-edge tip curl.  Tip curl must not extend more than dimension Z1 = 0.5 in. (12.7 mm) across the blade tip and not more than dimension Z = Replace pair of blades ifnot in the limits(Ref. TASK 72-21-00-300-002)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 1(143)