(2) Skin crack 0.25 in. (6.35 mm) maximum.

 C. Threaded parts and bosses  10 cycles
 (1) One crack 0.5 in. (12.7 mm) long providing
 there is no fluid or air leakage

 D. Stud on the aft face of the inner hub.
 (1) Missing/broken/loose stud(s):
 - One (1) or two (2) studs:  500hrs/500cyc

 - Three (3) studs: *If not adjacent to each other: 500hrs/500cyc *If two (2) non-serviceable studs are 500hrs/500cyc

 adjacent, but the third one is separated from them by two (2) serviceable studs: *If not: Replace studs

 - Four (4) studs or more:  Replace studs

 E. Thermal insulation blankets  100 cycles
 (1) Missing or protruding blankets
 F. Other areas  10 cycles
 (1) One crack 0.25 in. (6.35 mm) maximum
 F 『 EEFF : ALL E Page 69172-00-00
 E E Aug 01/05 ERE
ECES  E -------------------------------------------------------------------------------CONDITION MAX EXTENSION -------------------------------------------------------------------------------

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

13. Accessory gearbox
 A. Two opposite keylock studs missing provided there  3 cycles or 30
 is no leakage at flange hours

 B. Oil leakage from AGB/Starter carbon seal  10 cycles provided
 (Ref. TASK 79-00-00-210-003)  seal drain line is disconnected and drain cavity is capped
 5. Close-up
________
 Subtask 72-00-00-410-145
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the thrust reverser doors (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR

 Subtask 72-00-00-440-081
 B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 Subtask 72-00-00-410-146
 C. Close Access
 (1) Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 69272-00-00
 E E Aug 01/05 ERE
ECES  E TASK 72-00-00-200-026

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 Inspection/Check of the PS3 Line
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific plastic wire No specific warning notice No specific Torque Wrench : range 36.00 to 220.00 lbf.in
 (0.40 to 2.60 m.daN) No specific Torque Wrench : range 96.00 to 900.00 lbf.in
 (1.00 to 10.00 m.daN)
 B. Consumable Materials
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP1039 *
 acetone (Ref. 70-30-00) Material No. CP1041 *
 isopropyl alcohol (Ref. 70-30-00) Material No. CP2011 *
 stoddart solvent (Ref. 70-30-00) Material No. CP2101 *
 graphite grease (Ref. 70-30-00) Material No. CP2559 *
 ardrox 552 (Ref. 70-30-00) Material No. CP2560 *
 turco ind 79 (Ref. 70-30-00) Material No. CP2566 *
 mag-chem teksol (Ref. 70-30-00) Material No. CP2584 *
 degreasol 99 R (Ref. 70-30-00) Material No. CP2656 *
 mag-chem skysol (Ref. 70-30-00)
 F 『R EEFF : ALL E Page 69372-00-00

 E E Aug 01/05 E E ECES E -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

Material No. CP8001 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00) Material No. CP8002 * lockwire 0.032 in. (0.8 mm) dia. (Ref. 70-30-00)
 C. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
36-11-49-000-044 Removal of the High Pressure Tee Duct
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 1(62)