R Inspection/Check of the Fan-Outlet Guide Vanes (OGV) Figure 603/TASK 72-23-00-991-310- 13 (SHEET 1)
F 『 EEFF : ALL E Page 61672-23-00
E E Aug 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
R Inspection/Check of the Fan-Outlet Guide Vanes (OGV) Figure 603/TASK 72-23-00-991-310- 23 (SHEET 2)
F 『 EEFF : ALL E Page 61772-23-00
E E Aug 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
R Inspection/Check of the Fan-Outlet Guide Vanes (OGV) Figure 603/TASK 72-23-00-991-310- 33 (SHEET 3)
F 『 EEFF : ALL E Page 61872-23-00
E E Aug 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
C. Wear, fretting, If 0.02 in. (0,5 mm) 10 cycles serviceable
chafing on the top max. width and 0.8 in. extension is allowed.
of flange holes. (20 mm) max. length.
D. Washer impression If 0.032 in. (0,81 mm) 10 cycles serviceable
around flange max. depth and 0.60 in. extension is allowed. Do
holes (15,25 mm) max. blending (Ref. TASK 72-21-
diameter. 00-320-003) until high
metal is removed.
3. Fan inlet case on B1
upstream bracket
location
(Ref. Fig. 604/TASK
72-23-00-991-328)
A. Wear on B1 flange
radius.
R |__X___|__A___| ..
R |__X___|__A___|
R
R | 0,50 | 2,00 | ..
R | 6,50 | 0,68 |
R
R | 1,00 | 1,90 | ..
R | 7,00 | 0,57 |
R
R | 1,50 | 1,82 | ..
R | 7,50 | 0,48 |
R
R | 2,00 | 1,74 | ..
R | 8,00 | 0,39 |
R
R | 2,50 | 1,66 | ..
R | 8,50 | 0,32 |
R
R | 3,00 | 1,59 | ..
R | 9,00 | 0,25 |
R
R | 3,50 | 1,49 | ..
R | 9,50 | 0,19 |
R
F EEFF : ALL 『E Page 61972-23-00
E E Aug 01/05
E E
ECES E
F 『 E C F M E E E E 56-5B E
R Fan Inlet Case on B1 upstream bracket location Figure 604/TASK 72-23-00-991-328
F EEFF : E E ECES ALL 『E 72-23-00EEE Page 620 May 01/05
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
R | 4,00 | 1,35 | ..
R | 10,0 | 0,14 |
R
R | 4,50 | 1,19 | ..
R | 10,5 | 0,10 |
R
R | 5,00 | 1,04 | ..
R | 11,0 | 0,10 |
R
R | 5,50 | 0,91 | ..
R | 11,5 | 0,10 |
R
R | 6,00 | 0,79 | ..
R | 12,0 | 0,10 |
R
4. Fan rotor blades for:
(Ref. Fig. 605/TASK
72-23-00-991-325,
606/TASK 72-23-00-
991-326)
A. Cracks or tears
(1) Operational
cracks
(2) FOD caused
cracks or
tears.
F 『
EEFF : ALL E
E E
E E
ECES E
Not serviceable.
Not serviceable.
Replace pair of matchedblades (Ref. TASK 72-21-00-300-028)
Do blending procedure(Ref. TASK 72-21-00-320-003) until all indications are removed. Do a spot fluorescent-penetrant inspection to make sure that all indications are removed (Ref. TASK 70-51-00-230-002). Remove 0.010 in. (0.25 mm) additional material. Total blend must agree with the max repair limits as defined in figure
72-23-00Page 621
Aug 01/05
F 『 E C F M E E E E 56-5B E
R Fan Rotor Blades - Blend Limits Figure 605/TASK 72-23-00-991-325
F EEFF : E E ECES ALL 『E 72-23-00EEE Page 622 May 01/05
F 『
E C F M E
E E
E 56-5B E
E E
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發(fā)動機 1(142)
