曝光臺 注意防騙 網(wǎng)曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 CAUTION : DO NOT EXCEED THE SPEED OF 200 RPM TO APPROACH ALL_______
 ACOUSTICAL PANEL SCREWS BY USING PNEUMATIC OR ELECTRICAL
 SCREW DRIVERS. 
R  (4) Measure the self locking nut torque of each nut when you start to 
R  tighten the screw. 
R  NOTE : Make sure that the screws are not damaged, replace them if____ 
R  necessary. 
R  (a) If the self locking nut torque is less than 4.5 lbf.in (0.05 
R  m.daN), (Ref. TASK 72-23-00-400-043). 
R  (b) If the self locking nut torque is more than 4.5 lbf.in (0.05 
R  m.daN), but less than 31 lbf.in (0.35 m.daN), TORQUE the screws 
R  of fwd and mid panels to between 84 and 93 lbf.in (0.94 and 1.05 
R  m.daN) and TORQUE screws of the aft panels to between 66 and 75 
R  lbf.in (0.74 and 0.84 m.daN). 
R  (c) If the self locking nut torque is more than 31 lbf.in (0.35 
R  m.daN), but less than 49 lbf.in (0.55 m.daN), TORQUE screws at 
R  the running torque value and add 44 lbf.in (0.5 m.daN). 
R  (d) If the self locking nut torque is more than 49 lbf.in (0.55 
R  m.daN): 
R  - replace the self locking nut of the fwd panels (Ref. TASK 72-
23-00-300-045). 
R  - remove the engine (Ref. TASK 71-00-00-000-042) and do the 
R  engine shop repair procedure (Ref. ESM 722302300008) to replace 
R  the self locking of the mid and aft panels.

 E E May 01/05 E E ECES E 5. Close-up

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

________ Subtask 72-23-00-410-109
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the thrust reverser doors (Ref. TASK 78-36-00-410-040): FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR

 Subtask 72-23-00-440-066
 B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041) Subtask 72-23-00-410-110
 C. Close Access
 (1) Close the fan cowls: (Ref. TASK 71-13-00-410-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 (2) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 47972-23-00
 E E May 01/05 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 FAN FRAME ASSEMBLY - INSPECTION/CHECK

_____________________________________
 TASK 72-23-00-210-004
 Visual Inspection of the Fan Frame Assembly
 CAUTION : TITANIUM PARTS REQUIRE THE USE OF NON-HALOGENATED SOLVENTS.
_______
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific warning notice
 No specific Torque Wrench : range 36.00 to 220.00 lbf.in

 (0.40 to 2.60 m.daN)
 B. Referenced Information
 -------------------------------------------------------------------------------
REFERENCE DESIGNATION
 -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors
 71-13-00-410-040 Closing of the Fan Cowl Doors
R 72-23-00-000-027 Removal of the Fan Duct Panels 72-23-00-000-028 Removal of the Splitter Fairing 72-23-00-280-005 Inspection of Forward Acoustical Panels 72-23-00-280-006 Inspection of Mid Acoustical Panels 72-23-00-280-007 Inspection of Aft Acoustical Panels 72-23-00-300-042 Repair of Fan Duct Panel 72-23-00-350-002 Removal of Rust from the Fan Frame Casing
R 72-23-00-400-027 Installation of the Fan Duct Panels 72-23-00-400-028 Installation of the Splitter Fairing 78-30-00-081-041 Make the Thrust Reverser Serviceable after Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for Maintenance
 F 『 EEFF : ALL E Page 60172-23-00
 E E May 01/05 E E ECES E -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

78-36-00-010-040 Opening of the Thrust Reverser Doors
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發(fā)動機 1(138)