F  『
 E  C F M  E
 E  E

 E 56-5B E
 E E
 Subtask 72-62-00-010-058

 D. Open the thrust reverser doors: (Ref. TASK 78-36-00-010-040)
 FOR 1000EM1
 451AL, 452AR
 FOR 1000EM2
 461AL, 462AR

 4. Procedure_________
 (Ref. Fig. 401/TASK 72-62-00-991-300, 402/TASK 72-62-00-991-301, 403/TASK 72-62-00-991-302, 404/TASK 72-62-00-991-303, 405/TASK 72-62-00-991-304, 406/TASK 72-62-00-991-305, 407/TASK 72-62-00-991-306, 408/TASK 72-62-00-991-307, 409/TASK 72-62-00-991-308)
 Subtask 72-62-00-020-053
 A. Remove TGB external parts as follows:
 (1) Install a suitable container under the TGB to catch residual fluid draining from tubes and control.

 (2) Drain the TGB as follows:

 (a) Cut and remove the lockwire which safeties the drain plug (20) to the TGB.

 (b) Remove the drain plug (20) and let the oil drain.

 (c) Install the drain plug (20). Tighten by hand.

 (3) Loosen and remove the 4 bolts (110) securing the TGB scavenge tube

 (170) to the TGB housing (120) LH side.

 (4) Remove and retain gasket (90) located between TGB housing (120) and TGB scavenge tube flange.

 (5) Loosen and remove the 4 bolts (230) which secure the oil tank vent tube (220) assy to the TGB housing (120).

 (6) Remove and retain gasket (240) located between the oil tank vent tube

 (220) flange and the TGB housing (120).
 F 『 EEFF : ALL E Page 40372-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Drain Plug Removal
 Figure 401/TASK 72-62-00-991-300

 F 『 EEFF : ALL E Page 40472-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E

 Disconnection of Tubes on LH Side of TGB
 Figure 402/TASK 72-62-00-991-301
 F EEFF :  ALL  『E 72-62-00 Page 405 
E  E  Feb 01/98
 E  E
 ECES  E

R Disconnection of Brackets on RH and Lower Side of TGB Figure 403/TASK 72-62-00-991-302- 12 (SHEET 1)
 F 『 EEFF : ALL E Page 40672-62-00
 E E Aug 01/03 E E ECES E F 『 E C F M E E E E 56-5B E

R Disconnection of Brackets on RH and Lower Side of TGB Figure 403/TASK 72-62-00-991-302- 22 (SHEET 2)
 F 『 EEFF : ALL E Page 40772-62-00
 E E Aug 01/03 E E ECES E F 『 E C F M E E E E 56-5B E

 Installation of the TGB Turnbuckle
 Figure 404/TASK 72-62-00-991-303

 F 『 EEFF : ALL E Page 40872-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Removal of the TGB
 Figure 405/TASK 72-62-00-991-304

 F 『 EEFF : ALL E Page 40972-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Removal of the Mounting Pin
 Figure 406/TASK 72-62-00-991-305

 F 『 EEFF : ALL E Page 41072-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Extraction of Mounting Pin
 Figure 407/TASK 72-62-00-991-306

 F 『 EEFF : ALL E Page 41172-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Extraction of Radial Drive Shaft
 Figure 408/TASK 72-62-00-991-307

 F 『 EEFF : ALL E Page 41272-62-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Installation of Blanking Items on TGB Housing Ports
 Figure 409/TASK 72-62-00-991-308
 F EEFF :  ALL  『E 72-62-00 Page 413 
E  E  Feb 01/98
 E  E
 ECES  E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 (7) Loosen union nut.

 CAUTION : USE 2 WRENCHES TO REMOVE OR INSTALL THE TUBE COUPLING NUTS.
_______ ONE WRENCH TO HOLD THE UNION AND ONE TO LOOSEN OR TIGHTEN THE COUPLING NUT. THIS WILL PREVENT DAMAGE TO THE HARDWARE.
 (a) Loosen union nut (100) which attaches the securing TGB oil supply tube (180) to TGB housing (120).
 (8) Remove the two bolts (290) securing RH rear bracket (270) and the bleed bias bracket (280) to the right side of the TGB housing (120).

 (9) Remove the two bolts (360) securing bracket (60) on the rear face of the TGB housing (120).

 (10) Remove the two bolts (40 and 50) securing upper LH bracket (30) to the LH and rear side of TGB housing .
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(123)