(g) Install blanking plug on open ports of all tubes.
(2) Installation of the Handcranking assy: NOTE : You can ignore this step if the TGB is immediately replaced.
____
(a) Engage the horizontal drive shaft (Ref. TASK 72-63-00-860-001).
(b) Install the handcranking drive cover (Ref. TASK 72-63-00-400-002).
NOTE : Do not replace the O-rings of the handcranking drive
____ cover. New O-rings will be installed after reinstallation of the TGB.
Subtask 72-62-00-080-052
E. Removal of the TGB from the Tool.
(1) Hold the TGB and remove the rear lockpin of the FIXTURE, SUPPORT -TGB R/I (856A2719G02).
(2) Disengage the TGB from the support and place in a storage container.
F 『 EEFF : ALL E Page 41772-62-00
E E Aug 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 72-62-00-400-002
Installation of the Transfer Gearbox Module
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific hydraulic hoist platform
R No specific soft nose pliers No specific warning notice No specific Torque Wrench : range 36.00 to 220.00 lbf.in
(0.40 to 2.60 m.daN)
No specific Torque Wrench : range 96.00 to 900.00 lbf.in
(1.00 to 10.00 m.daN)
856A2537 1 PROTECTOR - MOUNTING PIN
856A2719 1 FIXTURE, SUPPORT - TGB R/I
856A2727 1 PULLER RADIAL DRIVE SHAFT
856A2805 1 TURNBUCKLE - TGB R/I
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2101 USA MIL-T-5544
graphite grease (Ref. 70-30-00)
Material No. CP2442 *
engine oil (Ref. 70-30-00)
Material No. CP8001 *
lockwire 0.032 in. (0.8 mm) dia (Ref. 70-30-00)
Material No. CP8002 *
lockwire 0.032 in. (0.8 mm) dia (Ref. 70-30-00)
F 『 EEFF : ALL E Page 41872-62-00
E E Aug 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
R 10 O-ring R 10 O-ring R 370 cotter pin R 420 O-ring R 420 O-ring R 430 O-ring R 430 O-ring R 450 O-ring R
D. Referenced Information72-62-00 05 -040 72-62-00 05 -040A 72-00-00 07 -070 72-63-00 04 -010 72-63-00 04 -010A 72-62-00 05 -030 72-62-00 05 -030A 72-62-00 05 -020
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R 12-13-79-610-002
R
R 12-13-79-610-002 71-00-00-710-006 71-00-00-710-025 71-13-00-010-040 71-13-00-410-040 72-63-00-000-002 72-63-00-400-002 72-63-00-860-001
78-30-00-081-041
78-30-00-481-041
78-36-00-010-040 78-36-00-410-040 79-00-00-210-003 80-11-10-400-002 72-62-00-991-300 72-62-00-991-301 72-62-00-991-302 72-62-00-991-303 72-62-00-991-304 72-62-00-991-305
F
EEFF : ALL
E
E
ECES
Check oil level and replenish Check Pop Out Indicator of EMCD (Electrical Master Chip Detector) Check oil level and replenish (Pressure Filling)Minimum Idle CheckAccel CheckOpening of the Fan Cowl DoorsClosing of the Fan Cowl DoorsRemoval of the Handcranking Drive CoverInstallation of the Handcranking Drive CoverDisengagement/Engagement of the Horizontal Drive ShaftMake the Thrust Reverser Serviceable after MaintenanceMake the Thrust Reverser Unserviceable for MaintenanceOpening of the Thrust Reverser DoorsClosing of the Thrust Reverser DoorsVisual Inspection of the Oil SystemInstallation of the Pneumatic StarterFig. 401Fig. 402Fig. 403Fig. 404Fig. 405Fig. 406
『
E 72-62-00Page 419
E Nov 01/03EE -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
F 『 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(125)
