(a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 F 『 EEFF : ALL E Page 60372-52-00
 E E May 01/05 ERE
ECES E Subtask 72-52-00-010-056

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 B. Get Access
 (1) Open the fan cowls doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR.

 (2) Put the access platform. Subtask 72-52-00-040-053

 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 72-52-00-010-057

 D. Open the thrust reverser cowl doors (Ref. TASK 78-36-00-010-040):
 FOR 1000EM1
 451AL, 452AR
 FOR 1000EM2
 461AL, 462AR.

 4. Procedure
_________ (Ref. Fig. 601/TASK 72-52-00-991-304, 602/TASK 72-52-00-991-300, 603/TASK 72-52-00-991-301, 604/TASK 72-52-00-991-302) Subtask 72-52-00-869-051
 A. Prepare for inspection:
 (1) Use the MONITOR, RESOLUTION BORESCOPE (856A1323G01) to make sure that the borescope or fiberscope and light source are serviceable. See the Non-Destructive Test Manual for this procedure (Ref. NTM 72-00-00).

 (2) Install the tools to turn the core engine. NOTE : The core engine may be turned using a breaker bar (see step

____ (a)) or with a drive motor (see step (b)).
 F 『 EEFF : ALL E Page 60472-52-00
 E E May 01/05 ERE
ECES E F 『 E C F M E E E E 56-5B E

 Core Rotation Drive Motor Installation
 Figure 601/TASK 72-52-00-991-304

 F 『 EEFF : ALL E Page 60572-52-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

 Inspection of the HPT Blade
 Figure 602/TASK 72-52-00-991-300

 F 『 EEFF : ALL E Page 60672-52-00
 E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E

R Rub Wear Notches on the Blade Tip and Cracks (Only Applicable NON /P Engines)

 Figure 603/TASK 72-52-00-991-301
 F EEFF :  ALL  『E 72-52-00 Page 607 
E  E  Aug 01/01
 E  E
 ECES  E

 F 『 E C F M E E E E 56-5B E

 High-Pressure Turbine Blade Inspection Areas (Only Applicable NON /P Engines)

 Figure 604/TASK 72-52-00-991-302
 F EEFF :  ALL  『E 72-52-00 Page 608 
E  E  Feb 01/98
 E  E
 ECES  E

 F 『 E C F M E E E E 56-5B E E E

 (a) To turn the core manually with a breaker bar, do the steps that follow:
 1 Remove the handcranking drive cover from the core rotation pad
_ on the left side of the accessory gearbox (AGB), opposite the starter (Ref. TASK 72-63-00-000-002).
 2 Install a 0.75 in. square drive socket with a 2ft. long
_ breaker bar into the handcranking drive pad. When you do the borescope inspection, turn the core engine clockwise (CW, aft looking forward).
 NOTE : To turn the core engine CW, the handcranking drive must
____ be turned counterclockwise (CCW).
 (b) To turn the core with a drive motor, do the steps that follow:
 1 Remove the starter (Ref. TASK 80-11-10-000-002).
_
 2 Install the MOTOR, DRIVE - CORE ENGINE ROTATION (856A1488 P01
_ or P02) into the accessory gearbox (AGB) starter drive pad. Align the drive shaft of the drive motor with the starter drive pad shaft and engage the splines.
 NOTE : The tool must be installed in the horizontal position
____ with the air hoses to the rear.
 3 Turn the tool until the captive bolts align with the gearbox
_
 bolt holes.

 4 Tighten the two captive bolts by hand.
_
 5 Install the clamp to secure the drive motor.
_
 6 Attach the foot or hand control air hoses to the quick
_
 disconnects on the tool.

 7 Connect the air supply to the drive motor. The air supply must
_ be capable of 100 psi (6.9 bar). The air supply must be lubricated and filtered at 6 SCFM (170 L/minute).
 (3) Remove one of the borescope plugs (S16 or S17) found immediately in front of the aft flange of the combustion case at the 5:30 and 8:30 o'clock positions.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(59)