F 『 EEFF : ALL E Page 60372-32-00
E E Nov 01/04 E E ECES E F 『 E C F M E E E E 56-5B E
Compressor Front Stator Assembly-Inspection
Figure 601/TASK 72-32-00-991-300
F EEFF : ALL 『E 72-32-00 Page 604
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
INTENTIONALLY BLANK
F 『R E E Page 60572-32-00
E E Nov 01/03 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E
R R Stator Vane ID to Rotor Contact Figure 602/TASK 72-32-00-991-304- 12 (SHEET 1)
F EEFF : E E ECES ALL 『E 72-32-00EEE Page 606 Nov 01/03
R R Stator Vane ID to Rotor Contact Figure 602/TASK 72-32-00-991-304- 22 (SHEET 2)
F EEFF : E E ECES ALL 『E 72-32-00EEE Page 607 Nov 01/03
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
- Damaged or broken lever arm bushing Bushing body is intactand provides 360 degrees support to lever arm pin
- Missing bushings Not serviceable
R R - Missing or broken bushing legs Any amount
3. Actuation ring connector for :
- Cracks (or broken) one side only Not serviceable
- Cracks (or broken) both sides Not serviceable
4. Vane lever arms, IGV's and stage 3 for :
- Broken or bent Not serviceable
- Cracked Not serviceable
- Nicks, dents and scratches Area A not serviceableArea B 0.010 in. (0.25 mm) after removal of high metal provided bottom of defect is not sharp pointed. Area C (not including pin) 0.002 in. (0.05 mm) deep.
Replace bushing
See limit extensions(Ref. TASK 72-00-00-200-025)
Remove engine for replacement of HPC rotor blades in one stage forward of and 2 stages aft of stage with defective lever arms
Replace lever arm (Ref. TASK 72-32-00-000-004) and (Ref. TASK 72-32-00-400-004)
F 『 EEFF : ALL E Page 60872-32-00
E E Nov 01/04 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
5. Vane lever arms, stage 1 and 2 for : (Ref. Fig. 601/TASK 72-32-00-991-300)
- Broken or bent
- Cracked
- Nicks, dents and scratches
6. Vane assembly, IGV's and stage 3 for :
- Looseness
7. Vane assembly, stages 1 and 2 for :Not serviceable
Not serviceable
Area A not serviceableArea B 0.010 in. (0.25 mm) after removal of high metal provided bottom of defect is not sharp pointed. Area C (not including pin) 0.002 in. ( 0.05 mm) deep.
Any amount of radial and side movement provided bushing not missing. No metal to metal contact allowed. (Listen for metallic sound while shaking vane stem)Remove engine for replacement of HPC rotor blades in one stage forward of and 2 stages aft of stage with defective lever arms
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發(fā)動機 2(32)
