__________ Subtask 72-23-00-941-091
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 72-23-00-010-113
B. Get Access
(1) Put an access platform in position at the front of the engine.
(2) Remove the spinner front cone (Ref. TASK 72-21-00-000-005).
(3) Remove the spinner rear cone (Ref. TASK 72-21-00-000-006).
(4) Put temporary mark on each fan blade from 1 to 36.
(5) Remove 3 consecutive fan blades (Ref. TASK 72-21-00-000-007). To compensate for imbalance caused by the removal of 3 blades, it is recommended to remove 3 blades 180 degrees opposite to those removed before.
F 『R EEFF : ALL E Page 65872-23-00
E E Aug 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
4. Procedure
_________
R (Ref. Fig. 609/TASK 72-23-00-991-311)
Subtask 72-23-00-350-059
A. Inspection of Mid Acoustical Panels
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Leading edge Not serviceable Replace panel (Ref. TASK
delamination 72-23-00-000-025) and
(Ref. TASK 72-23-00-400-
025)
2. Inner skin 20 percent of acoustical Above 20 percent, replace
delamination in area panel (Ref. TASK 72-23-00-
acoustical area 000-025) and (Ref. TASK
72-23-00-400-025)
3. Mid acoustical panel
cups
A. Dents, marks, No limits
indentations
caused by screw
head
B. Pierced cups No limits (Ref. TASK 72-23-00-400-
caused by screw 044)
head
C. Unbonded cups Not serviceable (Ref. TASK 72-23-00-300-
044)
D. Missing cups. Not serviceable (Ref. TASK 72-23-00-300-
044)
4. Missing panel Not serviceable
5. Loose bolts Not serviceable Tighten bolts
F 『R EEFF : ALL E Page 65972-23-00
E E Aug 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
6. Subsurface linear impressions or wrinkles
7. Voids
8. Defects in the protective coating (initial Tedlar film, or paint) such as:
A. Missing
B. Defects (dents, nicks, tears, flaking) that let show the inner skin
9. Inner skin defects, such as:
A. Superficial defects (dents, nicks, tears, impact marks) not through the skin
B. Defects (tears, cracks, punctures) through the skin No limits
Five per panel, 2 in.
(50.8 mm) apart, 0.12 in. (3 mm) Dia max,
0.012 in. (0.3 mm) max depth
No limits
No limits
No limits with a total surface area less than 4 square in. (2580 sq mm)per panel
Not serviceable
Serviceable criteria
applied on new parts
Serviceable criteria
applied on new parts
Remove the loose material
with a sharp blade
Remove the loose material
with a sharp blade
Remove the loose material
with a sharp blade
Replace panel(s)
(Ref. TASK 72-23-00-000-025) and (Ref. TASK 72-23-00-400-025)
F 『R EEFF : ALL E Page 66072-23-00
E E Aug 01/05 E E ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 72-23-00-410-104
A. Close Access
(1) Install the fan rotor blades at the locations recorded at the removal (Ref. TASK 72-21-00-400-007).
(2) Install the spinner rear cone (Ref. TASK 72-21-00-400-006).
(3) Install the spinner front cone (Ref. TASK 72-21-00-400-005).
(4) Make sure that the work area is clean and clear of tool(s) and other items. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(4)
