(5) TORQUE the nuts (60) to between 55 and 60 lbf.in (0.62 and 0.67 m.daN).

 (6) Depending on the drive pad on which you have replaced the sealol seal assembly, install one of these units:

 - fuel pump (Ref. TASK 73-11-10-400-003)

 - hydraulic pump (Ref. TASK 29-11-51-400-041)

 - IDG (Ref. TASK 24-21-51-400-040)

 - starter (Ref. TASK 80-11-10-400-002)

 F 『 EEFF : ALL E Page 81172-63-00
 E E May 01/05 ERE
ECES E Subtask 72-63-00-410-061

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 H. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR

 Subtask 72-63-00-710-054
 J. Do a leak check of the replacement seal (Ref. TASK 71-00-00-790-006). If there are leaks (Ref. TASK 71-00-00-790-002).
 5. Close-up
________ Subtask 72-63-00-942-050
 A. Remove the warning notice(s).
 F 『 EEFF : ALL E Page 81272-63-00
 E E May 01/05 ERE
ECES E

 F  『
 E  C F M  E
 E  E

 E 56-5B E E E TASK 72-63-00-300-003

 Replacement of a Magnetic Seal (Typical)
 1. Reason for the Job
__________________
 To replace a leaky magnetic seal by another magnetic seal at:
 - the Integrated Drive Generator (IDG) drive pad

 - the hydraulic pump drive pad

 - the fuel pump drive pad

 - the starter drive pad.

 NOTE : You can find two types of carbon seal installed on these Accessory
____ Gearbox (AGB) drive pads: a magnetic seal assembly or a sealol seal assembly. You can replace a magnetic seal assembly either, by a new magnetic seal assembly (the one without the thrust ring added) or, as an alternative, by a new sealol seal assembly.
 If you replace a magnetic seal by a sealol seal, remove the magnetic seal as specified in this procedure.
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific slide hammer No specific storage box No specific warning notice No specific Torque Wrench : range 36.00 to 220.00 lbf.in
 (0.40 to 2.60 m.daN) 856A1130 1 TOOL SET - JACK SCREW 856A3576 1 SEALOL AND MAGNETIC SEALS - R/I
 F 『 EEFF : ALL E Page 81372-63-00
 E E May 01/05 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E
 B. Consumable Materials

 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No.  CP1039 
R  Material No.  CP1041 
R 
R  Material No.  CP2011 
R 
Material No.  CP2101 
Material No.  CP2442 
R  Material No.  CP2559 
R 
R  Material No.  CP2560 
R 
R  Material No.  CP2566 
R 
R  Material No.  CP2584 
R 
R  Material No.  CP2656 
R 
C. Expendable Parts

*
 acetone (Ref. 70-30-00)
*
isopropyl alcohol (Ref. 70-30-00)
*
stoddard solvent (Ref. 70-30-00)
USA MIL-T-5544
 graphite grease (Ref. 70-30-00)
*
 engine oil (Ref. 70-30-00)
*
ardrox 552 (Ref. 70-30-00)
*
turco ind 79 (Ref. 70-30-00)
*
mag-chem teksol (Ref. 70-30-00)
*
degreasol 99 R (Ref. 70-30-00)
*
mag-chem skysol (Ref. 70-30-00)

 -------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
70  O-ring  72-63-00 02 -060
 70  O-ring  72-63-00 03 -060
 70  O-ring  72-63-00 05 -170
 70  O-ring  72-63-00 05A-170
 70  O-ring  72-63-00 06A-110
 90  O-ring  72-63-00 02 -070
 90  O-ring  72-63-00 03 -070
 90  O-ring  72-63-00 05 -160
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(151)