-------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
C. Radial cracks  Any amount.
 (convex or
 concave) within
 0.50 in. (12.7 mm)
 of trailing edge.
 D. Bent, curled or  Any amount above tip 
missing material.  shelf. 
E. Missing thermal  Any amount.
 barrier coating.
 3. Concave and convex
 surfaces for:
 A. Nicks or dents,  Any number 0.25 in.
 area A.  (6.35 mm) long.
 B. Nicks or dents,  Any number, 0.1 in.
 area B.  (2.54 mm) long.
 C. Nicks or dents,  3 permitted, 0.05 in.
 area C.  (1.27 mm) long. Nicks
 and dents must be
 separated by 0.125 in.
 (3.17 mm) minimum.
 D. Cracks,other  Not serviceable.
 areas.
 E. Missing thermal  Any amount.
 barrier coating.
 4. Blade airfoil for:
 A. Distortions or  Not serviceable.
 evidence of
 burning or
 melting.
 B. Missing thermal  Any amount.
 barrier coating.

See limit extensions(Ref. TASK 72-00-00-200-025).
 F 『 EEFF : ALL E Page 64872-52-00
 E E May 01/05 ERE
ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E

 (11) When the inspection is completed, turn off the BORESCOPE - LIGHT SOURCE SET (856A1322 P03, P04 or P07) and remove the FIBERSCOPE SET (856A1321 P01 or P03) and guide tube.

 (12) Install the spark igniter (Ref. TASK 74-21-30-400-002).

 (13) Tools used to rotate the core as follows:

 (14) Remove the tools used to rotate the core as follows:

 NOTE : If the breaker bar is installed see steps (a) and (b). If the
____ drive motor is installed see steps (c) and (d).
 (a) Remove the 0.75 in. (19.05 mm) square drive socket and 2 ft. (0.6 mm) breaker bar from the core rotation drive pad.

 (b) Install the handcranking drive pad cover (Ref. TASK 72-63-00-400-002).

 (c) Remove the drive motor from the starter pad of the AGB.

 (d) Install the starter (Ref. TASK 80-11-10-400-002).

 5. Close-up
________
 Subtask 72-52-00-410-058
 A. Close Access
 (1) Make sure that the work area is clean and clear of tool(s) and other items.

 (2) Close the thrust reverser doors (Ref. TASK 78-36-00-410-040). FOR 1000EM1 451AL, 452AR FOR 1000EM2 461AL, 462AR

 Subtask 72-52-00-440-054
 B. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041).
 F 『 EEFF : ALL E Page 64972-52-00
 E E May 01/05 E E ECES E Subtask 72-52-00-410-059

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

 C. Close Access
 (1) Close the fan cowls (Ref. TASK 71-13-00-410-040): FOR 1000EM1 437AL, 438AR FOR 1000EM2 447AL, 448AR.

 (2) Remove the access platform(s).

 (3) Remove the warning notice(s).

 F 『 EEFF : ALL E Page 65072-52-00
 E E May 01/05 E E ECES E HPT SHROUD AND STAGE 1 LPT NOZZLE ASSEMBLY - DESCRIPTION AND OPERATION

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E

______________________________________________________________________
 1. General
_______
 (Ref. Fig. 001)

 A. HPT shroud and stage 1 LPT nozzle assembly
 (1) The high pressure turbine (HPT) shroud and stage 1 low pressure turbine (LPT) nozzle assembly is located inside the aft end of the combustion case. It forms the interface between the core section and the LPT module of the engine. The forward flange of the assembly is rabbeted and bolted to the inner surfaces of the combustion case. The aft flange is bolted between the combustion case aft flange and the LPT stator forward flange.

 (2) The shroud/nozzle support has a thermal response matched to the rotor to provide good tip clearance control and structural stability. An air cavity between the shroud/nozzle support and the combustion case directs mixed 5th and 9th stage compressor bleed air onto the support and the outer, or backside, of the shrouds. This cooling air maintains closer clearances between the shrouds and the rotor blades.

 (3) The stage 1 LPT nozzles direct the core engine exhaust gas onto the stage one LPT blades. An air cavity between the stage one nozzle support and the combustion case directs 5th stage compressor bleed air through the nozzle vanes for cooling. After passing through the vanes, the air pressurizes and cools the cavity between the aft side of the HPT rotor and the forward side of the LPT rotor.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320飛機維護手冊 AMM ENGINE 發動機 2(72)