-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R AMM 34-22-25-170-001 Draining and Flushing of the Standby Static and R Standby Total Pressure lines (ISIS) R AMM 34-22-25-790-001 Low range Leak Test of the Standby Pneumatic circuits
 ASM 34-13/02
 SRM 530011P.BLOCK101
 TSM 34-13-00 P.Block 301 AIR DATA

 3. Fault Confirmation
__________________
 A. Test
 (1) Check Altitude/Airspeed tolerances (Ref. TSM 34-13-00 P.Block 301)

 - if within tolerances, no further actions required.

 (2) Visually check that the 2 quick-disconnect couplings of each ADM hose are properly attached to their respective probe.

 (3) Reconnect the couplings found disconnected, if any.

 NOTE : After the connection,
____
 - Make sure that a colored ring is shown on the quick disconnect coupling.

 - Pull the connectors to be sure that they are correctly

 attached. Perform an ADR SYSTEM TEST (Ref. AMM TASK 34-13-00-740-003). If the test is correct, no further maintenance action is required.
 (4) If all the quick-disconnect couplings are found to be properly attached, do the Functional Test of the Altitude and Airspeed Data (Ref. AMM TASK 34-13-00-720-009)
 4. Fault Isolation
_______________
 A. If the test shows a different altitude value from the ADR1 (compared to the ADR2 and ADR3) or from the ADR2 (compared to the ADR1 and ADR3) :
 - do a visual check of the static probes.
R (1) If one static probe is damaged, replace it (Ref. AMM TASK 34-11-16-R 000-001) and (Ref. AMM TASK 34-11-16-400-002).
 (2) Make sure that the small wing of the AOA sensor 1 , (2) or/and (3) is not damaged and that the mechanism moves freely.
R (a) If one AOA sensor is damaged, replace it (Ref. AMM TASK 34-11-19-R 000-001) and (Ref. AMM TASK 34-11-19-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-228, ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page B246
 May 01/05 CES

 (3) Do the flushing of the static pressure line of the Air Data Module (ADM 19FP4 and 19FP5 or 19FP6 and 19FP7) (Ref. AMM TASK 34-10-00-170-002).

 (4) Do the leak test of the main Air Data System (Ref. AMM TASK 34-13-00-790-002).

 (5) Do the functional test of the ADM for the CAPT (F/O) circuit (Ref. AMM TASK 34-11-00-720-001).

 (a) If one pressure value is different, replace the defective ADM (Ref. AMM TASK 34-11-17-000-001) and (Ref. AMM TASK 34-11-17-400-001).

 (b) If the pressure values are the same, replace the AOA sensor 1 ,(2) or /and (3) (Ref. AMM TASK 34-11-19-000-001) and (Ref. AMM TASK 34-11-19-400-001).

 (6) If the fault continues:

 - Do a check to make sure that there are no impacts on the fuselage around the AOA sensors, the static probes and the ADMs (Ref. SRM 530011P.BLOCK101).
R **ON A/C 001-049, 101-105, 151-199, 201-212, 214-220,
 B. If the test shows a different altitude value from the ADR3 (compared to the ADR1 and the ADR2):
 - do a visual check of the static probes.
R (1) If one static probe is damaged, replace it (Ref. AMM TASK 34-11-16-R 000-001) and (Ref. AMM TASK 34-11-16-400-002).
 (2) Make sure that the small wing of the AOA3 sensor is not damaged and that the mechanism moves freely.
R (a) If the AOA sensor 3 is damaged, replace it (Ref. AMM TASK 34-11-R 19-000-001) and (Ref. AMM TASK 34-11-19-400-001).
 (3) Do the draining and flushing of the standby static and the standby total pressure line of the Air Data Module (19FP8) (Ref. AMM TASK 34-10-00-170-003).

 (4) Do the leak test of the standby circuits (Ref. AMM TASK 34-21-00-790-001).

 (5) Do the functional test of the ADM for the standby circuit (Ref. AMM TASK 34-11-00-720-001).

 (a) If one pressure value is different, replace the defective ADM (Ref. AMM TASK 34-11-17-000-001) and (Ref. AMM TASK 34-11-17-400-001).
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-228, ∞∞34-13-00∞∞∞∞∞∞∞∞∞∞Page B247
 May 01/05 CES

 (b) If the pressure values are the same, replace the AOA sensor 3 (3FP3) (Ref. AMM TASK 34-11-19-000-001) and (Ref. AMM TASK 34-11-19-400-001).
 (6) If the fault continues:
 - Do a check to make sure that there are no impacts on the fuselage around the AOA sensor 3, the ADMs and the static probes (Ref. SRM 530011P.BLOCK101).
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導(dǎo)航 NAVIGATION 2(10)