3. Fault Confirmation
__________________
 A. Test Do the Interface test of the IR (system 2) (Ref. AMM TASK 34-14-00-740-001).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message WRG : SDI PIN PROG:
 - do a check of the SDI pin-programming pins AB/1A, 5A, 6A on the rack connector,

 - compare the status of the SDI pin-programming with the status given in the ASM (Ref. ASM 34-12/02).

 (1) If the pin programming is incorrect:

 - repair the wiring of the defective programming pins (Ref. ASM 34-12/02).

 (2) If the pin programming is correct:

 - replace the ADIRU-2 (1FP2) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-203, ∞∞34-14-00∞∞∞∞∞∞∞∞∞∞Page B200
 May 01/05 CES Failure of the IR 3 SDI Pin-Programming

 1. Possible Causes
_______________
 - ADIRU-3 (1FP3)

 - wiring of the defective programming pins

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3)
 AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3)
 AMM 34-14-00-740-001 Interface Test of the IR
 ASM 34-12/03

 3. Fault Confirmation
__________________
 A. Test Do the Interface test of the IR (system 3) (Ref. AMM TASK 34-14-00-740-001).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message WRG : SDI PIN PROG:
 - do a check of the SDI pin-programming pins AB/1A, 5A, 6A on the rack connector,

 - compare the status of the SDI pin-programming with the status given in the ASM (Ref. ASM 34-12/03).

 (1) If the pin programming is incorrect:

 - repair the wiring of the defective programming pins (Ref. ASM 34-12/03).

 (2) If the pin programming is correct:

 - replace the ADIRU-3 (1FP3) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
 B. Do the test given in Para. 3.
 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-203, ∞∞34-14-00∞∞∞∞∞∞∞∞∞∞Page B201
 May 01/05 CES TASK 34-14-00-810-963

 Loss of the IR1 Data Identified by the EFCS1
 1. Possible Causes
_______________
 - ADIRU-1 (1FP1)

 - wiring between the ADIRU 1 and the first terminal block

 - wiring between the ADIRU 1 and the terminal block 1831VT

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
31-32-00-810-934 Failure of the Digital Links AMM 27-96-00-740-001 BITE Test of the EFCS (Ground Scanning) AMM 34-12-34-000-001 Removal of the ADIRU (1FP1, 1FP2, 1FP3) AMM 34-12-34-400-001 Installation of the ADIRU (1FP1, 1FP2, 1FP3) ASM 34-14/01
 3. Fault Confirmation
__________________
 A. Test
 (1) Do the BITE test of the EFCS (Ground scanning) (system 1) (Ref. AMM TASK 27-96-00-740-001).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message IR1:
 - Replace the ADIRU-1 (1FP1) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
 (1) If the fault continues:
 - remove the ADIRU 1

 - do a check of the wiring between the ADIRU 1 and the first terminal block : for pins AB/5E, 6E of the ADIRU 1 (Ref. ASM 34-14/01)

 (a) If the wiring is not ok:
 - repair it

 - install the ADIRU 1.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-14-00∞∞∞∞∞∞∞∞∞∞Page B202
 May 01/05R
 CES  (b) If the wiring is ok:
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 2(83)