_______________
R - FCU (2CA) R - wiring R 2. Job Set-up Information
______________________
R A. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R AMM 22-81-12-000-001 Removal of the FCU (2CA)
R AMM 22-81-12-400-001 Installation of the FCU (2CA)
R AMM 34-13-00-740-002 INTERFACE TEST of the ADR
R ASM 34-13/02

R 3. Fault Confirmation

__________________ R A. Test R (1) Do the interface test of the ADR (systems 1 and 3) (Ref. AMM TASK 34-
R 13-00-740-002). R 4. Fault Isolation
_______________
R A. If the test gives the maintenance messages FCU (2CA) /ADIRU1 (1FP1) and
R FCU (2CA) /ADIRU3 (1FP3):
R - replace the FCU (2CA) (Ref. AMM TASK 22-81-12-000-001) and (Ref. AMM
R TASK 22-81-12-400-001).

R (1) If the fault continues:
R - do a check and repair the wiring of the DIGITAL BARO CORRECTION A
R bus from the FCU (2CA) to the first terminal block (Ref. ASM 34-R 13/02).

R B. Do the test given in Para. 3.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-81∞∞∞∞∞∞∞∞∞∞Page 230
 Aug 01/01 CESR (1) Do the interface test of the ADR 1 (2 or 3) (Ref. AMM TASK 34-13-00-R 740-002).

R  TASK 34-13-81-810-827 
R  Failure of the ADR ZERO MACH-AOA Pin-Programming 
R  1. Possible Causes_______________ 
R  - ADIRU-1 (1FP1) 
R  - ADIRU-2 (1FP2) 
R  - ADIRU-3 (1FP3) 
R  - wiring ZERO MACH-AOA pin-programming of the ADIRU-1 (2 or 3) 
R  2. Job Set-up Information______________________ 
R  A. Referenced Information 
R  -------------------------------------------------------------------------------
R  REFERENCE  DESIGNATION 
R  -------------------------------------------------------------------------------

R  AMM 34-12-34-000-001  Removal of the ADIRU (1FP1, 1FP2, 1FP3) 
R  AMM 34-12-34-400-001  Installation of the ADIRU (1FP1, 1FP2, 1FP3) 
R  AMM 34-13-00-740-002  INTERFACE TEST of the ADR 
R  3. Fault Confirmation__________________ 
R  A. Test 

R 4. Fault Isolation
_______________
R A. If the test gives the maintenance message WRG: ZERO MACH-AOA PIN PROG:
R - remove the ADIRU-1 (2 or 3) (Ref. AMM TASK 34-12-34-000-001).
R - do a check of pin AA/5H and AA/5J on the rack connector.
R - make sure that there is no ZERO MACH-AOA pin-programming on these pins.

R (1) If the pin-programming is correct:
R - install a new ADIRU-1 (1FP1) (ADIRU-2 (1FP2) or ADIRU-3 (1FP3))
R (Ref. AMM TASK 34-12-34-400-001).

R (2) If the pin-programming is incorrect:
R - remove the wiring ZERO MACH-AOA pin-programming of the ADIRU-1 (2
R or 3) of pin AA/5H and pin AA/5J.

R B. Do the test given in Para. 3.

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-13-81∞∞∞∞∞∞∞∞∞∞Page 231
 Nov 01/04 CESR **ON A/C 301-399, 401-499,

 TASK 34-13-81-810-828
 Loss of the ADR 1 Data Identified by the DMC 1
 1. Possible Causes
_______________
 - ADIRU-1 (1FP1)

 - DMC-1 (1WT1)

 - wiring

 2. Job Set-up Information
______________________
 A. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM  31-63-34-000-001 
AMM  31-63-34-400-001 
AMM  34-12-34-000-001 
AMM  34-12-34-400-001 
AMM  34-13-00-740-002 
ASM  34-13/01

 3. Fault Confirmation
__________________
 A. Test
Removal of the DMC (1WT1,1WT2,1WT3)Installation of the DMC (1WT1,1WT2,1WT3)Removal of the ADIRU (1FP1, 1FP2, 1FP3)Installation of the ADIRU (1FP1, 1FP2, 1FP3)INTERFACE TEST of the ADR
R  Do the interface test of the ADR (system 1) (Ref. AMM TASK 34-13-00-740-002).
 4. Fault Isolation
_______________
 A. If the test gives the maintenance message
 ADIRU1 (1FP1)/DMC1 (1WT1):

R  - replace the ADIRU-1 (1FP1) (Ref. AMM TASK 34-12-34-000-001) and (Ref. AMM TASK 34-12-34-400-001).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 導航 NAVIGATION 2(21)