- replace DATA MEMORY MODULE (DMM) (P20) (Ref. AMM TASK 49-73-32-000-001) and (Ref. AMM TASK 49-73-32-400-001).

 (b) If the resistance values are in the specified limits:

 - replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
 C. If the APU GND SCANNING menu gives the maintenance message:
 DATA MEMORY MODULE P20
 associated with Fault Code Number (FCN) 242 or 243
 - do a check for damage/contamination of the electrical connector P20 of the DATA MEMORY MODULE (DMM)
 (1) If the electrical connector P20 of the DMM is damaged/contaminated:

 - do a repair/cleaning.

 (2) If the electrical connector P20 of the DMM is OK:

 - replace DATA MEMORY MODULE (DMM) (Ref. AMM TASK 49-73-32-000-001) and (Ref. AMM TASK 49-73-32-400-001).
 (a) If the fault continues:
 - replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
 **ON A/C 001-049, 101-105, 151-199, 201-210,
 Post SB 49-1062 For A/C 001-049,101-105,151-154,201-207,
 A. If the APU GND SCANNING menu gives the maintenance message:
 DATA MEMORY MODULE (8062KM)
 associated with Fault Code Number (FCN) 240
 - do a check for damage/contamination of the electrical connector P20 of the DATA MEMORY MODULE (DMM)
 (1) If the electrical connector P20 of the DMM is damaged/contaminated:

 - do a repair/cleaning.

 (2) If the electrical connector P20 of the DMM is OK:

 - disconnect the electrical connector P20 at the DMM/APU interface.

 - do a check and repair of the aircraft wiring from the ECB (59KD) AB/F11,F7 to structural ground; required value > 100 kOhms and the ECB (59KD) AB/F11 to AB/F7; required value > 100 kOhms, (Ref. ASM 49-61/01).

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-70-00∞∞∞∞∞∞∞∞∞∞Page 220
 201-210, Config-2 Aug 01/05 CES

 - put a jumper across the sockets 8 and 9 of the electrical connector P20 of the DMM on the APU harness side.

 - do a check and repair of the aircraft wiring from the ECB (59KD) AB/F11 to AB F7; required value < 10 Ohms and the ECB (59KD) AB/J2,J3 to structural ground; required value > 100 kOhms and the ECB (59KD) AB/J2 to AB/J3; required value > 100 kOhms, (Ref. ASM 49-61/01).

 - put a jumper across the sockets 10 and 11 of the electrical connector P20 of the DMM on the APU harness side.

 - do a check and repair of the aircraft wiring from the ECB (59KD) AB/J2 to AB/J3; required value < 10 Ohms and the ECB (59KD) AB/C6 to structural ground; required value > 100 kOhms and the ECB (59KD) AB/C6 to AB/F11; required value > 100 kOhms, (Ref. ASM 49-61/01).

 - put a jumper across the sockets 6 and 7 of the electrical connector P20 of the DMM on the APU harness side.

 - do a check and repair of the aircraft wiring from the ECB (59KD) AB/C6 to AB/F11; required value < 10 Ohms, (Ref. ASM 49-61/01).

 (a) If the resistance values are out of the specified limits:

 - replace DATA MEMORY MODULE (DMM) (8060KM) (Ref. AMM TASK 49-73-32-000-001) and (Ref. AMM TASK 49-73-32-400-001).

 (b) If the resistance values are in the specified limits:

 - replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
 B. If the APU GND SCANNING menu gives the maintenance message:
 DATA MEMORY MODULE (8062KM)
 associated with Fault Code Number (FCN) 241 or 244
 - do a check for damage/contamination of the electrical connector P20 of the DATA MEMORY MODULE (DMM)
 (1) If the electrical connector P20 of the DMM is damaged/contaminated:

 - do a repair/cleaning.

 (2) If the electrical connector P20 of the DMM is OK:

 - disconnect the electrical connector P20 at the DMM/APU interface.

 - do a check and repair of the aircraft wiring from the ECB (59KD) AB/F11,F7 to structural ground; required value > 100 kOhms and the ECB (59KD) AB/F11 to AB/F7; required value > 100 kOhms,

 「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 151-199, 201-210, ∞∞49-70-00∞∞∞∞∞∞∞∞∞∞Page 221
 Config-2 May 01/05 CES (Ref. ASM 49-61/01).

 - put a jumper across the sockets 8 and 9 of the electrical connector P20 of the DMM on the APU harness side.

 - do a check and repair of the aircraft wiring from the ECB (59KD) AB/F11 to AB F7; required value < 10 Ohms and the ECB (59KD) AB/J2,J3 to structural ground; required value > 100 kOhms and the ECB (59KD) AB/J2 to AB/J3; required value > 100 kOhms, (Ref. ASM 49-61/01).
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 2(167)