(2) If the fault continues:
- replace the OIL FILTER DIFFERENTIAL PRESSURE SWITCH P5 of the gen scavenge pump filter (Ref. AMM TASK 49-91-14-000-001) and (Ref. AMM TASK 49-91-14-400-001).
(3) If the fault continues:
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-001) and (Ref. AMM TASK 49-61-34-400-001).
R **ON A/C 063-099, 401-499,
A. If the test gives the maintenance message:
OIL FILTER SWITCHES (8070KM)/(8071KM)
with the LRU TROUBLE SHOOT DATA menu information:
OIL FILTER SWITCH SHOWS ELECTRICAL GROUND
Fault Code Number: 101
- do a check and repair the wiring from the ECB (59KD) AB/C11 to the OIL FLITER DIFFERENTIAL-SWITCH (8070KM) (lube pump filter) and OIL FILTER DIFFERENTIAL-SWITCH (8071KM) (generator scavenge filter) (Ref. ASM 49-61/02).
(1) If the fault continues:
- replace the OIL FILTER DIFFERENTIAL PRESSURE SWITCH (8070KM) of the lube pump filter (Ref. AMM TASK 49-91-15-000-001) and (Ref. AMM TASK 49-91-15-400-001).
(2) If the fault continues:
- replace the OIL FILTER DIFFERENTIAL PRESSURE SWITCH (8071KM) of the gen scav pump filter (Ref. AMM TASK 49-91-14-000-001) and (Ref. AMM TASK 49-91-14-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-003, 051-099, 401-499, ∞∞49-90-00∞∞∞∞∞∞∞∞∞∞Page 202
Config-1 Aug 01/05 CES (3) If the fault continues:
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-001) and (Ref. AMM TASK 49-61-34-400-001).
R **ON A/C 001-003, 051-099, 401-499,
B. Do the test given in para. 3.
OIL ((131-9(A))) - FAULT ISOLATION PROCEDURES
_____________________________________________
TASK 49-90-00-810-812
Lube Pump Filter SW P9/GEN SCAV Filter SW P5 Fault (131-9(A))
1. Possible Causes
_______________
- OIL FILTER SWITCH SHOWS ELECTRICAL GROUND
- damage/contamination of the electrical connector P9 and P5
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 49-00-00-860-008 APU Start by External Power (131-9(A))
AMM 49-00-00-860-009 APU Shutdown by External Power (131-9(A))
AMM 49-11-11-000-004 Removal of the Power Plant (APU) (131-9(A))
AMM 49-11-11-400-004 Installation of the Power Plant (APU) (131-9(A))
AMM 49-61-34-000-003 Removal of the Electronic Control Box (ECB)
(131-9(A)) AMM 49-61-34-400-003 Installation of the Electronic Control Box (ECB) (131-9(A)) AMM 49-91-14-000-002 Removal of the Oil Filter Differential Pressure Switches (8070KM) (131-9(A)) AMM 49-91-14-400-002 Installation of the Oil Filter Differential Pressure Switches (8070KM) (131-9(A))
3. Fault Confirmation
__________________
A. Read-out of ECB Trouble Shooting Data
(1) Put the APU MASTER SW to the ON position.
(2) Get access to the APU LAST LEG/PREVIOUS LEG report.
(3) Push the '>' adjacent to the related CFDS failure message:
- the MCDU menu shows:
OIL FILTER SWITCH SHOWS ELECTRICAL GROUND
- do the Fault Confirmation that follows:
(a) Start the APU (Ref. AMM TASK 49-00-00-860-008).
(b) Get access to the APU GND SCANNING menu.
(c) Shut down the APU (Ref. AMM TASK 49-00-00-860-009).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-90-00∞∞∞∞∞∞∞∞∞∞Page 201
201-210, Config-2 Aug 01/05 CES
(d) Wait until the ECB (59KD) power-down, speed < 7% plus 30 seconds.
(e) Get access to the APU GND SCANNING menu.
4. Fault Isolation
_______________
R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If the APU GND SCANNING menu gives the maintenance message:
LUBE PUMP FILTER SW P9 / GEN SCAV FILTER SW P5
associated with Fault Code Number (FCN) 101
- do a check for damage/contamination of the electrical connector P9 and P5 of the LUBE PUMP FILTER / GENERATOR SCAV FILTER.
(1) If the electrical connector P9 and/or P5 is damaged, do a repair. If it is
- contaminated, clean it.
(2) If the electrical connector are servicable. 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 2(171)
