(2) Get access to the APU SHUTDOWN report.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A222
201-210, Config-1 Aug 01/05 CES (3) Push the '>' adjacent to LRU DATA:
- the MCDU menu shows
DEOIL SOLENOID SHOWS OPEN CIRCUIT
DEOIL SOLENOID SHOWS CIRCUIT FAILURE
(4) Start the APU and apply Bleed Air for 20 seconds, minimum (Ref. AMM TASK 49-00-00-860-008).
4. Fault Isolation
_______________
R **ON A/C 001-049, 101-105, 107-107, 151-154, 201-207,
A. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
NO ACCELERATION
DEOIL SOLENOID P15
associated with the Fault Code Number (FCN) 133
- do a check for damage/contamination of the electrical connector P15 of the DE-OIL SOLENOID VALVE (P15)
(1) If the electrical connector P15 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector P15 is OK:
- use a multimeter to do a resistance check across the pin 1 to the pin 2 of the DE-OIL SOLENOID VALVE (P15)
(a) If the resistance value is > 80 Ohms:
- replace the DE-OIL SOLENOID VALVE (P15) (Ref. AMM TASK 49-91-49-000-003) and (Ref. AMM TASK 49-91-49-400-003).
(b) If the resistance value is in the specified limit:
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/J4 to the DE-OIL SOLENOID (P15) P15/1 and the DE-OIL SOLENOID (P15) P15/2 to GND (Ref. ASM 49-61/01).
1 If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
B. If an APU auto shutdown occurs during the APU operation and the APU SHUTDOWN report gives the maintenance message:
NO ACCELERATION
DEOIL SOLENOID P15
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-199, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A223
201-210, Config-1 Aug 01/05 CES associated with the Fault Code Number (FCN) 134
- do a check for damage/contamination of the electrical connector P15 of the DE-OIL SOLENOID VALVE (P15)
(1) If the electrical connector P15 is damaged/contaminated:
- do a repair/cleaning.
(2) If the electrical connector P15 is OK:
- use a multimeter to do a resistance check across pin 1 and pin 2; required value > 10 Ohms and pin 1 and pin 3; required value > 100 kOhms of the DE-OIL SOLENOID VALVE (P15)
(a) If the resistance values are out of the specified limits:
- replace the DE-OIL SOLENOID VALVE (P15) (Ref. AMM TASK 49-91-49-000-003) and (Ref. AMM TASK 49-91-49-400-003).
(b) If the resistance values are in the specified limits:
- use a multimeter to do a resistance check across pin 2 and pin 3; required value > 10 Ohms and pin 2 and pin 15; required value > 100 kOhms of the DATA MEMORY MODULE (P20)
1_ If the resistance values are out of the specified limits:
- replace the DATA MEMORY MODULE (P20) (Ref. AMM TASK 49-73-
32-000-001) and (Ref. AMM TASK 49-73-32-400-001).
2 If the resistance values are in the specified limits:
_
- do a check and repair of the aircraft wiring from the ECB (59KD) AB/J4 to the DE-OIL SOLENOID (P15) P15/1 and the DE-OIL SOLENOID (P15) P15/2 to GND and the ECB (59KD) AB/J4 to the DATA MEMORY MODULE (P20) P20/2 and the DATA MEMORY MODULE (P20) P20/2 to GND (Ref. ASM 49-61/01).
a If the fault continues:
_
- replace the ECB (59KD) (Ref. AMM TASK 49-61-34-000-003) and (Ref. AMM TASK 49-61-34-400-003).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 101-105, 107-107, 151-154, ∞∞49-00-81∞∞∞∞∞∞∞∞∞∞Page A224
201-207, Config-1 Aug 01/05 CES
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：A320 Trouble Shooting Manual 排故手冊 機載輔助動力 2(81)
