S 863-011
(2)
At the overhead panel, P5, set each switch for the outboard landing lights to the extend position.
(a) Make sure the outboard landing lights extend fully down.
S 863-012
(3) Open these circuit breakers and attach the DO-NOT-CLOSE tags:
(a) On the load control center panel, P18: 1) RIGHT OUTBOARD LANDING LIGHT 2) LEFT OUTBOARD LANDING LIGHT
S 643-013
(4) Lubricate the sector gear of each outboard landing light (Fig. 301).
E. Put the Airplane to Its Usual Condition
S 863-014
(1) Remove the DO-NOT-CLOSE tag and close each circuit breaker that was opened.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
12-25-95
ALL ú ú 01 Page 301 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
M77 IS OPTIONAL TO DC77
OUTBOARD LANDING LIGHT
(EXTENDED)
Outboard Landing Light Lubrication
Figure 301
B55362
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
12-25-95
ALL ú
ú 01 Page 302
ú Jul 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
(2) S 863-015Set each switch to the retract position. (a) Make sure the outboard landing lights retract.
(3) S 863-008Remove electrical power if it is not necessary (AMM 24-22-00/201).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
12-25-95
ALL ú ú 01 Page 303 ú Mar 15/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
CABLE LUBRICATION - SERVICING
_____________________________
1. General_______
A. There is one task in this procedure, the lubrication of the control cables.
TASK 12-26-00-603-001
2. Control Cable Lubrication_________________________
A. Consumable Materials
(1)
D00015 Grease - Corrosion Preventive, BMS 3-24, BMS 3-33
(2)
G01043 Cloth - Lint-Free
B. Access
(1) Location Zone
200 Lower Half of the Fuselage
300 Left Wing
400 Right Wing
500 Left Nacelle
600 Right Nacelle
700 Empenage
C. Procedure
S 163-002
CAUTION: DO NOT USE SOLVENT OR HEAT TO THIN THE GREASE ON THE CONTROL
_______ CABLES. DO NOT USE SOLVENT TO CLEAN THE CONTROL CABLES. THE SOLVENT REMOVES GREASE FROM THE CABLE. DO NOT APPLY OR SPRAY BMS 3-23 ON THE CONTROL CABLES.
(1) Use a lint-free cloth that is clean and dry to clean the control cables.
NOTE: Remove the old grease and dirt from the surface of the
____ control cable. Clean the control cable for the full length of the cable for the full length of travel through fairleads, air pressure seals, over pulleys, quadrants, and drums.
S 643-003
(2) Lubricate the control cables:
(a) Carbon Steel Cables:
CAUTION: THE CONTROL CABLES IN THE WING AND NACELLE AREA ARE
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 SERVICING(133)
