-
The door latches

 -
The uplock mechanism

 -
The uplock hook

 -
The downlock mechanism

 -
The bungee springs

 -
The lock actuators

 -
The position indication switches.

 It is the airline's decision to apply or not apply anti-icing fluid as protection after the ice is removed.
 3)  Make sure that ice did not collect on the steering cables for the nose wheel. Remove the ice if it is necessary.
 4)  Examine the alternate extend system for ice that has collected in these areas that are open and not heated: a) Examine control cables for landing gear extension
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-33-01
 ALL  ú ú 02 Page 315 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 b) The external mechanism for the landing gear
 CAUTION: DO NOT MOVE THE AIRPLANE IF THE TIRES FREEZE TO THE
_______ GROUND. MAKE SURE THE WHEELS TURN WHEN YOU MOVE THE AIRPLANE.
 5)  Remove the ice and snow from the ground areas around the landing gear. This will make it less possible that the tires will freeze to the ground. This will also prevent unwanted airplane movement because of the wind or engine operation. a) Use warm air or deicing fluid to release the tires from
 the ground or to remove frozen material. b) Salt is not recommended since it can collect on the metal parts and cause corrosion.
 (g) Wing Fuel Tanks 1) Frost can occur on the bottom of the wings in the fuel tank areas in temperatures above freezing. This is caused by the condensation of moisture in the air when it touches cold surfaces that are below freezing. The frost will usually melt when you add fuel that is at a higher temperature. If the frost continues and is more than 1/8 inch thick, remove it before the takeoff.
 2)  Clear ice can occur on the top of the wing when these conditions occur:
 -
The temperature of the fuel in the tank is below freezing.

 -
The ambient temperature is above freezing.

 -There is rain, drizzle or fog.
 Carefully examine the top of the wing to see if there is clear ice. Use the equipment that is necessary to get sufficient access to the top of the wing to do this check. It is possible that the clear ice can only be found by touch. You must remove clear ice and anti-ice the wing, if it is necessary, before the takeoff.
 (h) Miscellaneous 1) Pitot Probe, Static Ports, and Total Air Temperature (TAT) Probes (Fig. 303) a) Look for ice that is attached to the surface 4 feet or less from the pitot inlets, static port, and TAT probe inlets. Remove all the ice in these areas. b) Do not point a spray of deicing/anti-icing fluid directly at or into the pitot inlets, static ports, or the TAT probes.
 c)  If ice causes a blockage of the static openings, carefully apply warm air until the ice melts. d) If you applied too much fluid to the fuselage near the static ports, examine the nearest in-line drain.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-33-01
 ALL  ú ú 02 Page 316 ú Nov 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL

TOTAL AIR TEMPERATURE PROBE
PITOT-STATIC PROBE (4 LOCATIONS)
Balance Panel and Probe Location
Figure 303

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-33-01
 ALL  ú ú 02 Page 317 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
G69247
AIRPLANE
NOSE DOWN

AIRPLANE
NOSE UP

AIRPLANE
NOSE DOWN

AIRPLANE
NOSE UP

AIRPLANE
NOSE DOWN

AIRPLANE
NOSE UP

A

737-300/400/500MAINTENANCE MANUAL
SURFACE AT FULL "DN" WILL NOT PERMIT DEICE RUN-OFF ENTRY INTO BALANCE PANEL
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 SERVICING(161)