ICE-SNOW-SLUSH RUN-OFF WHEN USING DEICING FLUID

SLUSH OR ICE BLOCKING FULL

Horizontal Stabilizer Position
Figure 304

G69248
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-33-01
 ALL  ú ú 02 Page 318 ú Mar 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 2)  Drains
 a)  Examine all of the waste water and condensate drains on the airplane to make sure there are not blockages because of ice or other material. It is not necessary to put a plug on the drains during the ice removal or anti-icing procedure. But, do not point a fluid spray at these drain areas.
 3)  Air stairs
 a)  Retract the stairs as soon as possible. Too much ice or snow will not collect on the stairs if you do the brush or sweep away the snow that collects. If ice is still there, remove with the ice removal fluid. Be careful not to point the spray into the door openings.
 4)  Angle-of-Attack Sensor (Fig. 303)
 a)  Make sure that no ice and/or snow is on the sensors. Make sure the sensors are free to move. Apply deicing fluid if it is necessary.
 5) Windshield Wiper Blades a) Remove the ice that collected on the windshield wiper blades.
 E.  Hot Water Ice Removal Procedure
 S 663-044
 (1)  
You can use hot water at 180-200°F maximum tank temperature to remove ice and snow from the airplane surfaces when the ambient temperature is 27°F, stable or on the increase.

 S 663-045

 (2)  
To prevent the water from freezing again you must apply anti-icing fluid to the surface immediately after you remove the ice with hot water.

 S 663-046

 (3)  
Add 10% glycol to the hot water tank. This will keep to a minimum the freezing of the remaining water in the equipment you used to remove the ice.

 F.  One-Step Ice Removal/Anti-Icing Procedure
 S 663-047
 (1)  You can do the one-step ice removal/anti-icing procedure, with the deicing/anti-icing fluid heated to 180-200°F. Use this procedure to remove the ice and snow from the airplane when the temperature is below 28°F. After you use the mixture to make the airplane surfaces clear, the remaining fluid will give some anti-icing protection. If the material/deicing fluid that you wanted to remove freezes before it flows off the airplane, it shows that an incorrect mixture of anti-icing fluid was used. You must apply more anti-icing fluid to get more protection.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 12-33-01
 ALL  ú ú 02 Page 319 ú Jul 12/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 663-048
 (2)  The fluid mixed with the water can be Type I deicing (ice removal)/anti-icing fluid, Type II, or Type IV deicing/anti-icing fluid. The holdover time will be longer with the Type II and Type IV deicing/anti-icing fluids. With each fluid, you must use the data that follows to find the quantity of fluid to use in the mixture.
 (a)  
The airline experience

 (b)  
The fluid specifications

 (c)  
The manufacturer's recommendataions

 (d)  
The weather conditions

 S 663-049
 (3)  If you must remove more ice, or it is necessary to do the anti-icing procedure before the subsequent flight, do the full ice removal/anti-icing procedure.
 G. Two-Step Ice Removal/Anti-Icing Procedure
 S 663-050
 (1)  
The two-step ice removal/anti-icing procedure is usually the recommended procedure when the precipitation conditions are continuous. The second step must be done no more than 3 minutes after you begin the first step. Do the procedure area by area if it is necessary.

 S 663-051

 (2)  
The items that follow will have an effect on the holdover time you get after you do the anti-icing procedure.

 (a)  
The fluid that was used

 (b)  
The weather conditions

 S 213-062
 (3)  
Thus, you must do frequent inspections to see if it is necessary to apply more fluid.
　
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 SERVICING(162)