S 022-005
(2)
Remove the four bolts that attach the shutoff valve to the modular package.
S 492-006
CAUTION:_______DO NOT LET HYDRAULIC FLUID GET ON EQUIPMENT. IF HYDRAULIC FLUID GETS ON EQUIPMENT, IMMEDIATELY CLEAN IT FROM THE EQUIPMENT. HYDRAULIC FLUID CAN CAUSE DAMAGE TO EQUIPMENT.
(3)
Put a container below the shutoff valve to catch the hydraulic fluid.
S 022-007
(4)
Carefully turn and pull directly up on the shutoff valve to remove it from the modular package.
S 032-008
(5)
Put a cover on the modular package to keep dirt out.
TASK 27-81-91-402-009
3. Leading Edge Standby Drive Shutoff Valve Installation (Fig. 201)_____________________________________________________
A. Consumable Materials
(1)
D00196 Fluid - Hydraulic, BMS 3-11
(2)
D00567 Lubricant - Skydrol Assembly Lube
B.
References
(1)
12-12-00/301, Hydraulic Reservoir
C.
Access
(1)
Location Zone
216 Main Wheel Well, LH
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-91
ALL ú ú 01 Page 203 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
D. Procedure
S 432-010
(1)
Install the five O-rings with the backup rings on the shutoff valve.
S 642-011
(2)
Lightly lubricate the O-rings and the backup rings with hydraulic fluid or assembly lube.
S 422-012
(3)
Carefully put the shutoff valve in the modular package.
S 432-013
(4)
Install the four bolts that attach the shutoff valve to the modular package.
S 862-014
(5)
Tighten the bolts to 30-40 pound-inches.
S 432-015
(6)
Install lockwire on the four bolts.
S 432-016
(7)
Connect the electrical connector to the valve motor.
S 862-044
(8)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a)
P6-2 Circuit Breaker Panel
1) FLAP SHUTOFF VALVES
(9)
Do a test of the shutoff valve.
(10)
Fill the hydraulic reservoir if it is necessary (Ref 12-12-00/301).
S 712-017
S 612-018
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
27-81-91
ALL ú ú 01 Page 204 ú Nov 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
TASK 27-81-91-002-019
4. Standby Drive Shutoff Valve Motor Removal (Fig. 201)_________________________________________
A. Access
(1)
Location Zone
216 Main Wheel Well, LH
B.
Procedure
S 862-020
(1)
Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a)
P6-2 Circuit Breaker Panel
1) FLAP SHUTOFF VALVES
S 032-021
(2)
Disconnect the electrical connector from the valve motor.
S 862-047
(3)
Put the flap shutoff valve lever to position 2.
S 432-022
(4)
Remove the four screws that attach the valve motor to the shutoff valve.
S 022-023
(5)
Remove the valve motor from the shutoff valve.
TASK 27-81-91-402-048
5. Standby Drive Shutoff Valve Motor Installation (Fig. 201)______________________________________________
A. Access
(1)
Location Zone
216 Main Wheel Well, LH
B.
Procedure
(1) 中國航空網 www.k6050.com 航空翻譯 www.aviation.cn 本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(104)
