曝光臺 注意防騙 網曝天貓店富美金盛家居專營店坑蒙拐騙欺詐消費者

 (r)  Remove electrical power (AMM 24-22-00/201).
 (s)  Remove the DO-NOT-OPERATE tag from the ELEC 1, HYD PUMPS B
 switch.
 (t)  Remove the DO-NOT-OPERATE tag from the ENG 2 HYD PUMPS B
 switch.
 (u)  Put the ENG 2 HYD PUMP switch (P5 panel) back to the ON
 position.
 (v)  Make sure the ELEC 1, HYD PUMPS SYS B switch is in the ON
 position.
 (w)  Remove the DO-NOT-OPERATE tag from the system B ground
 pressurization module in the rear end of the forward right hand
 air conditioning compartment (next to the wheel well/forward
 end).
 (x)  Remove the DO-NOT-CLOSE tags and close these circuit breakers:
 1) P6-2 Circuit Breaker Panel
 a) PTU/LG BYP V CONT 1
 b) PTU/LG BYP V CONT 2
 2) P6-11 Circuit Breaker Panel
 a) STBY HYD PUMP NORMAL
 b) ELEC HYD PUMP SYS B
 3) P6-12 Circuit Breaker Panel
 a) STBY HYD PUMP (ALT)
 (y)  Make sure the pressure from hydraulic systems B and Standby are
 released (AMM 27-81-00/201).
 (z)  Remove the lock on the standby hydraulic module (Fig. 201):
 1) Connect the electrical connector to the leading edge
 devices shutoff valve at the standby hydraulic module.
 2) Make sure the override lever at the leading edge devices
 shutoff valve is in position 1 (leading edge flaps and
 slats retracted).
 3) Remove the lock on the shutoff valve.
 4) Remove the lockpin.

 (aa) Set the alternate flap arm switch to ARM.
 (ab) Make sure the standby hydraulic system low pressure light is off.
 (ac) Monitor the leading edge flaps and slats for 60 seconds.
 (ad) Make sure the flaps and slats do not extend.
 NOTE: The leading edge flaps can slowly extend because of
____ gravity.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-00
 ALL  ú ú 01 Page 216 ú Nov 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (ae) Set the alternate flap arm switch to OFF.
 (af) Remove "DO NOT DRIVE MOTOR ENGINE WITH THE THRUST REVERSER COWLS OPEN" placard from engine start switch, if it is not necessary.
 G. Put the Airplane Back to Its Usual Condition
 S 862-037
 (1)  Release the pressure from hydraulic system A if it is not necessary (AMM 29-09-00/201).
 TASK 27-81-00-402-032
 5.  Leading Edge Flap and Slat Locks Installation_____________________________________________
 A. Special Tools and Equipment
 (1)  
F80048-84, -89, or -90 - Leading Edge Flap Actuator Locks

 (2)  
C27012-1 - Leading Edge Slat Actuator Lockout Set

 (3)  
F80049-12 - Flight Controls Lock Assembly

 B.
Access

 (1)  
Location Zone
 216 Main Wheel Well, LH
 217 Main Wheel Well, RH
 302 Outboard Leading Edge with Slats, LH
 303 Inboard Leading Edge with Slats, LH
 402 Outboard Leading Edge with Slats, RH
 403 Inboard Leading Edge with Slats, RH

 C.
Procedure

 S 482-033
 (1)  
Install the leading edge flap and slat locks to prevent retraction of the flaps and slats:

 (a)  
Pressurize hydraulic system B (par. 2).

 (b)  
Move the flap control lever to the 10-unit detent to fully extend the leading edge devices.

 (c)  
Release pressure from hydraulic system B (par. 3).

 WARNING: MAKE SURE TO INSTALL THE LEADING EDGE FLAP AND SLAT LOCKS
_______ TO PREVENT ACCIDENTAL OPERATION OF THE LEADING EDGE FLAPS AND SLATS. THE LEADING EDGE FLAPS AND SLATS CAN MOVE QUICKLY. THIS CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
 (d)  Install the leading edge flap and slat locks on the extended leading edge flap and slat actuators.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-81-00
 ALL  ú ú 01 Page 217 ú Jul 12/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(27)