737-300/400/500
MAINTENANCE MANUAL

1 8
NO. 0
9
GROUND SPOILER
ACTUATOR (EXAMPLE)
SEE A HYDRAULIC LINES
PISTON ROD MOUNTING BOLT GROUND
SEE B SPOILER
PISTON
ROD
BRACKET
SWIVEL MOUNTING
JOINT BOLTS
SPLIT BALL BEARINGS
PILLOW
BLOCK
OUTBD
PILLOW BLOCK
MOUNTING BOLT

FWD ACTUATOR
GROUND SPOILER ACTUATOR (EXAMPLE)
A

No. 0, 1, 8 and 9 Ground Spoiler Actuator Installation
Figure 401 (Sheet 1)

EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-94
 ALL  ú ú 01 Page 403 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 (b)  
Remove the caps from the hydraulic ports.

 (c)  
Install the O-rings and the unions in the actuator.

 S 424-011
 (3)  
Install the spoiler actuator (Fig. 401):

 (a)  
Put the actuator in its position and make sure the hydraulic lines align with the fittings.

 (b)  
Install the mounting bolt for the piston rod end with the head outboard.

 (c)  
Apply the grease to the split ball bearings.

 (d)  
Assemble the split ball bearings in the pillow block.

 (e)  
Make sure the ball bearings move freely.

 (f)  
Put the pillow blocks on the actuator.

 (g)  
Install the mounting bolts for the pillow block.

 (h)  
Tighten the bolts to 225-275 pound-inches.

 (i)  
Install the washer and locknut on the bolt in the piston rod end.

 (j)  
Tighten the nut to 660-780 pound-inches.

 (k)  
Install the bracket on the actuator with the two bolts. 1) Install the lockwire on the bolts.

No. 0, 1, 8 and 9 Ground Spoiler Actuator Installation
Figure 401 (Sheet 2)

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 27-62-94
 ALL  ú ú 01 Page 404 ú Jul 15/91
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A 737-300/400/500MAINTENANCE MANUAL
 S 434-012
 (4)  
Connect the hydraulic lines to the actuator:

 (a)  
Make sure that the hydraulic system A is not pressurized.

 (b)  
Remove the plugs from the hydraulic lines.

 (c)  
Connect the hydraulic lines to the actuator.

 (d)  
Tighten the hydraulic fittings.

 S 864-013
 (5)  
Pressurize the hydraulic reservoirs (Ref 29-09-00/201).

 S 864-014

 (6)  
Put the SPOILER A and B switches in the OFF position.

 S 864-015

 (7)  
Supply the system A hydraulic power (Ref 27-62-00/201).

 S 874-016

 (8)  
Move the speed brake control lever to bleed the spoiler actuators.

 S 794-017

 (9)  
Make sure there is no leakage of hydraulic fluid at the actuator.

 S 824-018

 (10)
 Do the adjustment and the test of the ground spoiler actuator (Ref 27-62-94/501).

 D.
Put the Airplane Back to Its Usual Condition

 S 014-019
 (1)  
Close the access panel on the trailing edge flaps if it is necessary.

 S 864-020

 (2)  
Retract the trailing edge flaps if it is necessary.

 S 864-021

 (3)  
Lower the spoilers if it is necessary.

 (4)  
Remove the system A hydraulic power (Ref 27-62-00/201).

 (5)  
Put the SPOILER A and B switches in the ON position.

 (6)  
Remove the electrical power (Ref 24-22-00/201).

 S 864-022
 S 864-023
 S 864-024
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 飛行操縱 FLIGHT CONTROLS 6(9)