(4)
Put the SPEED BRAKE lever on the control stand in the DN position.

 (5)  
Put the stabilizer position pointer in the green band.

 S 865-067
 S 865-068
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-26-00
 ALL  ú ú 10 Page 523 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 485-079
 (6)  With the thrust levers at the idle position, put the protractor with
 the adapter on the thrust levers.
 (a) Set the protractor to 0 degrees (Fig. 501).
 S 865-080
 (7)  To prevent the operation of the Takeoff Warning horn when you move
 the thrust levers, put the airplane in the simulated AIR MODE.
 (a) There are two different procedures to put the airplane into the
 simulated air mode:
 1) Push and hold the air sensing switch (S1) on the E11
 landing gear logic shelf.
 CAUTION: CAREFULLY PULL THE TELEFLEX CABLE UNTIL THE AIR MODE_______
 SENSOR OPERATES. IF YOU ARE NOT CAREFUL, YOU CAN
 CAUSE DAMAGE TO THE AIR MODE SENSOR TARGET BRACKET.
 2) Disconnect and extend the teleflex cable on one of the main
 gear upper torsion links.
 S 865-081
 (8)  Move the two thrust levers to a position of more than 33 degrees
 from the idle position.
 S 865-082
 (9)  Make sure the control lever for the landing gear is in the DN (down)
 position.
 (a) All the green landing gear lights will be on.
 S 495-209

 WARNING: YOU MUST CAREFULLY INSTALL THE GROUND LOCKS IN ALL LANDING
_______ GEAR. AN ACCEDENTAL RETRACTION OF THE LANDING GEAR CAN CAUSE INJURY TO PERSONS AND DAMAGE TO EQUIPMENT.
 (10)
 Make sure you install the ground lock assemblies in all landing gear (AMM 32-00-01/201).

 S 485-064

 (11)
 Make sure that the external hydraulic pressure supply is connected to hydraulic systems A and B (AMM 29-15-00/201).

 (a)  Pressurize hydraulic systems A and B to 3000 psi (AMM 29-15-00/201, and AMM 27-51-00/201).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 31-26-00
 ALL  ú ú 07 Page 524 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
 S 865-313
 (12) Extend the trailing edge flaps to the 1-unit position
 (AMM 27-51-00/501).

 (a)  Make sure the flaps extend to the 1-unit position.
 H. Thrust Lever/Landing Gear Warning Test (landing gear position simulated).
 NOTE: Do the Prepare-To-Test tasks first.
____ S 865-211
 (1) Put the nose gear in a simulated retracted position as follows:
 (a)  
Put the landing gear lever in the off position. 1) Make sure that all the red landing gear lights come on. 2) Make sure all the green landing gear lights stay on and you

 do not hear the warning horn.

 (b)  
Put an aluminum or copper deactuator shield between the lock sensor switch S846 and the steel actuator of the nose gear.

 NOTE: Switch S846 is on the lock brace of the nose gear.
____
 1) Make sure the green nose gear light goes off.
 (c)  Put an aluminum or copper deactuator shield between the nose gear down sensor switch S845 and the steel actuator arm.
 NOTE: The switch is above the trunnion pin of the left nose
____
 gear.

 1) Make sure the green nose gear light stays off.
 (d)  Remove the aluminum or copper deactuator shield from the lock sensor switch S846. 1) Make sure the red nose gear light on the P2 panel goes off.
 S 865-213
 (2)  Move the No. 1 thrust lever to the idle position.
 (a)  
Make sure you hear the continuous horn when the thrust lever is less than 8.5 degrees forward of the idle position.

 (b)  
Make sure the red light for the nose gear comes on.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機維護手冊 儀表 INSTRUMENTS(139)