S 865-430
(7) If you will do no more tests, then do this task: "Put the Airplane to its Usual Condition."
TASK 31-24-02-735-186
39. Hydraulic System Low Pressure Signals Test
__________________________________________
A. References
(1) AMM 29-00-00/201, Hydraulic Power
B. Access
(1) Location Zones
101 Control Cabin - Left
102 Control Cabin - Right
C. Procedure
S 865-691
(1) Make sure you did the Prepare For Input Parameter Test task.
S 865-188
CAUTION: MAKE SURE THE THRUST REVERSER COWLS (C-DUCTS) ARE IN THE CLOSED
_______ POSITION BEFORE YOU DO THIS TEST. YOU CAN CAUSE DAMAGE TO THE FLAPS AND COWLS IF THE COWLS ARE OPEN WHEN THE FLAPS EXTEND.
(2) Make sure these circuit breakers are closed:
(a) P6-3 Panel
1) C00313, MASTER DIM SECTION 1
2) C00318, MASTER DIM SECTION 6
S 865-692
(3)
Make sure the hydraulic systems A, B, and STBY are off.
S 735-190
(4)
Do a test of the system A eng low pressure signal.
(a) Set the portable tester to SUBFRAME 1, WORD 13.
1) Make sure the system A-ENG 1 LOW PRESSURE light on the P5 forward overhead panel is on.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
BEJ 101-112, 114-999; ú 31-24-02
ú ú 12 Page 548 ú Mar 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
737-300/400/500MAINTENANCE MANUAL
2) Make sure the BIT 2 light on the portable tester is off.
(b)
Open this circuit breaker:
1) P6-3 Panel
a) MASTER DIM SECTION 6
(c)
Disconnect electrical connector D2684 from the low pressure switch S796 for the system A engine pump.
(d)
Close this circuit breaker:
1) P6-3 Panel
a) MASTER DIM SECTION 6
(e)
Make sure the BIT 2 light on the portable tester is on.
(f)
Make sure the system A-ENG 1 LOW PRESSURE light is off.
S 735-191
(5) Do a test of the system B eng low pressure signal.
(a)
Set the portable tester to SUBFRAME 1, WORD 21.
(b)
Make sure the system B-ENG 2 LOW PRESSURE light on the P5 forward overhead panel is on.
(c)
Make sure the BIT 1 light on the portable tester is off.
(d)
Open this circuit breaker:
1) P6-3 Panel
a) MASTER DIM SECTION 5
(e)
Disconnect electrical connector D2686 from the low pressure switch S797 for the engine pump for system B.
(f)
Close this circuit breaker:
1) P6-3 Panel
a) MASTER DIM SECTION 5
(g)
Make sure the BIT 1 light on the portable tester is on.
(h)
Make sure the system B-ENG 2 LOW PRESSURE light is off.
(i)
Open these circuit breakers:
1) P6-3 Panel
a) MASTER DIM SECTION 1
b) MASTER DIM SECTION 5
c) MASTER DIM SECTION 6
(j)
Connect the electrical connectors to the low pressure switches for system A and B engine pumps.
(k)
Close these circuit breakers:
1) P6-3 Panel
a) MASTER DIM SECTION 1
b) MASTER DIM SECTION 5
c) MASTER DIM SECTION 6
S 735-192
(6) Do a test of the low pressure signals for system B elec.
(a)
Set the portable tester to SUBFRAME 1, WORD 29.
(b)
Make sure the system B-ELEC 1 LOW PRESSURE light is on.
(c)
Make sure the BIT 2 light on the portable tester is off.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù.
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：737-300 400 500 AMM 飛機(jī)維護(hù)手冊(cè) 儀表 INSTRUMENTS(76)
