NOTE: Drill through the hole in the hook to drill the hole in
____
 the hook support fitting.

 (b)  Manually apply alodine to the inside of the hole.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-00
 ALL  ú ú 01 Page 804 ú Jun 10/90
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 (c)  Paint the inside of the hole with primer.
 S 828-017
 (6)  
Adjust the hook closed switch (AMM 52-34-00/501).

 S 828-018

 (7)  
Adjust the Hook Position Switch.

 (a)
Manually turn the hook actuator two turns counterclockwise.

 NOTE:____This is the hooks rigged closed position. The rigging pin hole in the hook should align with the hole you put in the hook support fitting.

 (b)  
Turn the hook actuator 112 turns counterclockwise.

 NOTE: For the aft door, between 110 and 112 turns
____
 is satisfactory.

 (c)  
Make sure the clearance between the hook and the external stop is between 0.001 and 0.032 inches.

 (d)  
Turn the hook actuator clockwise until the hook touches the external stop.

 (e)  
Make sure the hook position switch operates at the correct time. 1) Turn the hook actuator 8.5 turns counterclockwise.

 NOTE: The switch roller should be approximately in the
____ middle of the actuator ramp at this point.
 2)  Make sure there is continuity between pins 7 and 11 of connector P3 on the cargo door junction box.
 NOTE: Before the switch operates, there is no continuity
____ between pins 7 and 11 of the P3 connector.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-00
 ALL  ú ú 01 Page 805 ú Oct 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 3)  Move the switch in its bracket if it is necessary to make the switch operate.
 S 868-012
 (8)  
Close circuit breakers as follows for applicable cargo door.

 (a)  
P59 Aft Equipment Panel
 1) AFT CARGO DOOR POWER UNITS

 (b)  
P414 Power Distribution Center - Left
 1) 414A21 LOWER CARGO DOOR FWD
 2) 414F15 CARGO DOOR CONTROL FWD
 3) 414F16 CARGO DOOR CONTROL CONTROL AFT

 S 718-015
 (9)  
Do a check of the cargo door system (Ref 52-34-00/601).

 (10)
 Install the lower door lining on the door.

 S 418-016
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 52-34-00
 ALL  ú ú 01 Page 806 ú Oct 10/94
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400 MAINTENANCE MANUAL
 FORWARD/AFT CARGO DOOR - REMOVAL/INSTALLATION
_____________________________________________
 1.  General
_______
 A.  This procedure contains two tasks:
 (1)  
The first task is the removal of the forward/aft cargo door from the airplane.

 (2)  
The second task is the installation of a forward/aft cargo door on the airplane.

 B.  
You can install the door on its hinges with the airplane on its gear.

 C.  
You must connect the lift mechanism and adjust the forward cargo door with the airplane on its gear with the operating weight empty, or leveled on jacks.

 TASK 52-34-01-004-001
 2.  Forward/Aft Cargo Door - Removal
________________________________
 A.  Special Tools and Equipment
 (1)  
30HME65B04308-1 Sling - Fwd and Aft Cargo Doors

 (2)  
TME65B04308-1 Dolly - Cargo and Main Entry Door

 (3)  
2TME65B04308-1 Dolly - Forward and Aft Lower Lobe Cargo Door (optional to TME65B04308-1)
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 艙門 DOORS 3(39)