(2)  
AMM 71-11-04/201, Fan Cowl Panels

 (3)  
AMM 71-11-06/201, Core Cowl Panels

 (4)  
AMM 78-31-00/201, Thrust Reverser System

 D.
Access

 (1)  
Location Zone
 412 Engine 1 - HPC Case 4 o'clock
 422 Engine 2 - HPC Case 4 o'clock
 432 Engine 3 - HPC Case 4 o'clock
 442 Engine 4 - HPC Case 4 o'clock

 (2)  
Access Panel
 416 Right Thrust Reverser Half - Engine 1
 426 Right Thrust Reverser Half - Engine 2
 436 Right Thrust Reverser Half - Engine 3
 446 Right Thrust Reverser Half - Engine 4

 E.
Procedure

 S 424-057-N00
 (1)  
Install the fuel distribution-valve strainer:

 (a)  
Lubricate the packings (1, 2, 8, and 9) with petrolatum.

 (b)  
Install the strainer (24) in the fuel distribution valve: 1) Install the packing (1) in the groove of the strainer (24). 2) Install the strainer (24) in the fuel distribution valve.

 (c)  
Install the transfer tube (6) and the strainer cover (3): 1) Install the packings (8 and 9) in the grooves on the

 transfer tube (6). 2) Install the transfer tube (6) into the strainer cover (3).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-04
 ALL  ú ú N01 Page 407 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
3)  Install the strainer cover (3) and the transfer tube (6) on the fuel distribution valve: a) Install the packing (2) in the groove of the strainer
 cover (3). b) Lubricate the threads of the bolts (5) with engine oil. c) Install the strainer cover (3) with the washers (4) and
 bolts (5).
 NOTE: You must install the retaining bolts (14 and 15)
____ after you set the adapter (21) and the bracket (16) on the strainer. The position for the retaining bolts is at the four sides of the strainer cover.
 d)  Tighten the bolts (5) to 30-33 pound-inches (3.4-3.7 newton-meters).
 (d)  Install the adapter (21) on the transfer tube (6): 1) Put the gasket (7) on the transfer tube (6).
 NOTE: Align the hole in the gasket with the recess in the
____
 flange of the transfer tube.

 2)  Move the transfer tube (6) forward against the fuel flow transmitter.
 NOTE: Make sure the alignment pin in the flange of the
____ fuel flow transmitter engages the recess in the transfer tube flange.
 3)  Put the adapter (21) on the transfer tube (6).
 NOTE: Make sure the slot in the adapter forward flange
____ engages the pin in the aft face of the transfer tube flange.
 4)  Install the forward end of the adapter (21) and the transfer tube (6): a) Lubricate the bolts (23) with engine oil. b) Attach the adapter (21) and the transfer tube (6) to
 the fuel flow transmitter with the bolts (23) and washers (22). c) Tighten the bolts (23) to 85-95 pound-inches (9.6-10.7 newton-meters).
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-04
 ALL  ú ú N01 Page 408 ú Jun 18/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
d) Safety the bolts (23) with lockwire or safety cable and safety cable ferrule. 5) Install the bracket (16) and the adapter aft end (21): a) Lubricate the threads of the bolts (14 and 15) with engine oil. b) Put the bracket (16) on the aft end of the adapter (21). c) Attach the bracket (16) and the adapter aft end (21) to the strainer cover (3) with the bolts (14 and 15). d) Tighten the bolts (14 and 15) to 85-95 pound-inches (9.6-10.7 newton-meters).
 (e)  
Lubricate the threads of the bolts (10) with engine oil.

 (f)  
Attach the clamps (11, 13, 17, 19, 20) to the bracket (16) with the bolts (10) and nuts (12).

 F.
Return the Aircraft to its Usual Condition

 S 414-052-N00
 WARNING: OBEY THE INSTRUCTIONS IN AMM 78-31-00/201 WHEN YOU CLOSE THE
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 1(40)