(n)  
Lubricate the threads of the bolts (117) with engine oil.

 (o)  
Attach the clamps (118) to the brackets on the diffuser case and the No. 8 fuel injector with the bolts (117) and nuts (116). 1) Tighten the nuts (116) with your hand.

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-05
 ALL  ú ú N01 Page 471 ú Jun 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / PW4000 SERIES /747-400 / ENGINES/MAINTENANCE MANUAL ////////////////////////
(p)  
Tighten the bolts (123, 125, 126, 127 and 128) at each end of the duct (115), from one corner to the opposite corner, to 85-95 pound-inches (9.6-10.7 newton-meters).

 (q)  
Tighten the bolts (123, 125, 126, 127 and 128) again to 85-95 pound-inches (9.6-10.7 newton-meters) until you keep the necessary torque.

 (r)  
Install the lockwire on the bolts (123, 125, 126, 127 and 128) to the diffuser case.

 S 434-208-N00
 (4)  
Attach the fuel manifold clamp (57) to the bracket on the diffuser case.

 (a)  
Lubricate the threads of the bolt (55) with engine oil.

 (b)  
Attach the clamp (57) with the bolt (55) and the nut (56).

 1)  Tighten the nut (56) to 36-40 pound-inches (4.1-4.5 newton-meters).
 S 414-209-N00
 (5)  
Attach the heat shield (107) on the engine with the steps that follow (Refer to Fig. 402, Sheet 2):

 (a)  
Install the heat shield (107) on the engine to the brackets with the screws (108) and washers (109) and the bolts (104), washers (105) and nuts (106). 1) Tighten the nuts (106) and the screws (108).

 S 414-210-N00
 (6)  
Connect the cable (100) for the exciter-to-igniter plug to the lower igniter plug (Fig. 402, Sheet 1).

 (a)  
Lubricate the threads of the coupling nut for the cable (100) with the antiseize compound.

 (b)  
Connect the coupling nut to the igniter plug.

 (c)  
Tighten the coupling nut to 140-160 pound-inches (15.8-18.1 newton-meters).

 NOTE: Make sure the coupling nut is tightened to the
____ correct torque value . An incorrect tightened coupling nut can cause high ignition noise which can have an effect on the airplane radio equipment.
 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú

 73-11-05
 ALL  ú ú N01 Page 472 ú Oct 10/97
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
(d)  
Put the heat shields (101, 103) on the cable (100).

 (e)  
Bend the tabs of the heat shields (101, 103) into the groove in the igniter plug boss.

 (f)  
Attach the heat shields (101, 103) with the clamp (102).

 (g)  
Tighten the clamp (102) to 40-45 pound-inches (4.5-5.1 newton-meters).

 S 414-211-N00
 (7)  
Install the starter (AMM 80-11-01/401).

 H.
Return the Aircraft to its Usual Condition

 S 864-212-N00
 (1)  
For the applicable engine, remove the DO-NOT-CLOSE tag and close this circuit breaker:

 (a)  
P6 Main Power Distribution Panel
 1) 6L10 FUEL CONT VALVE ENG 1
 2) 6L11 FUEL CONT VALVE ENG 2
 3) 6L12 FUEL CONT VALVE ENG 3
 4) 6L13 FUEL CONT VALVE ENG 4

 S 864-213-N00
 (2)  
For the applicable engine, remove the DO-NOT-CLOSE tags and close these circuit breakers:

 (a)  
P6 Main Power Distribution Panel
 1) 6F1 IGN 1 ENG 1
 2) 6F2 IGN 1 ENG 2
 3) 6F3 IGN 1 ENG 3
 4) 6F4 IGN 1 ENG 4
 5) 6K19 IGN 2 ENG 1
 6) 6K20 IGN 2 ENG 2
 7) 6K21 IGN 2 ENG 3
 8) 6K22 IGN 2 ENG 4
 9) 6G19 STBY IGN ENG 1
 10) 6G20 STBY IGN ENG 2
 11) 6G21 STBY IGN ENG 3
 12) 6G22 STBY IGN ENG 4

 EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：747-400 AMM 飛機維護手冊 發動機燃油和控制 1(72)