09P1181B
09P1181A
09P1180
Roller Bearing (02-390)
Case (02-450)
ACTUATOR- INSTALLATION OF THE ROLLER BEARING (02-390) (Sheet 3 of 4)
Figure 6001/GRAPHIC 21-53-12-991-015-A01

Page 6006

02-430 02-440 02-410 02-450B

ACTUATOR- BEARINGS AND LIP SEAL LOCATION (Sheet 4 of 4)
Figure 6001/GRAPHIC 21-53-12-991-015-A01

Page 6007 / 6008
21-53-12 JUN 15/10

TASK 21-53-12-300-802-A01
2. REPAIR 02 - ACTUATOR - REPLACEMENT OF EQUIPPED PLATE PARTS
A. Reason For The Job
(1) Use this procedure when it becomes necessary to replace the Equipped Plate parts.
B. Job Set-Up Information
(1)
Tools, Features and Equipment

(a) Equivalent alternatives may be used for the listed items.

(2)
Consumable Material

REFERENCE  QTY  NAME 
09P1231  1  Removal tool for lip seal and roller bearing 
09P1181A  1  Installation tool for roller bearing 
09P1181B  1  Installation tool adaptor 
09P1180  1  Centering tool 
09P1524  1  Removal plate tool 
No specific  1  Hydraulic press 
No specific  1  Heating unit 
No specific  1  Manual press 

(a) Equivalent alternatives may be used for the listed items.
REFERENCE  NAME 
95° ETHYL ALCOHOL  Cleaning fluid 
(M26C) AEROSHELL 7  Grease 

Page 6009
21-53-12 JUN 15/10
(3)  Referenced Information
REFERENCE  PAGE BLOCK  DESIGNATION 
(refer to Page Block 10001)  10001  ILLUSTRATED PARTS LIST 
(Ref. to Fig. 6002)  6001  ACTUATOR - REMOVAL AND INSTALLATION OF THE LIP SEAL (02-070) AND OF THE ROLLER BEARING (02-060) 

C.  Job Set-Up Not Applicable
D.  Procedures WARNING: PROTECT YOURSELF WHEN YOU TOUCH THE PLATE (02-150) AT 150 °C
(320 °F). CAUTION: DO NOT APPLY HEAT LONGER THAN NECESSARY. NOTE: CLEAN ALL METALLIC SURFACES BY USING 95° ETHYL ALCOHOL CLEANING
FLUID BEFORE INSTALLATION. NOTE: THE NUMBERS IN PARENTHESIS AFTER THE COMPONENT DESCRIPTION ARE THE FIGURE AND THE ITEM NUMBERS OF THE IPL (refer to Page Block 10001). Subtask 21-53-12-350-003-A01
(1)  Removal
(a)
 Lightly tap the plate to remove the Ball Bearings  (02-080), (02-090), (02-100) and if applicable (02-100) and (02-110).

(b)
Heat the plate to remove the 3 Pins (02-050).

(c)
If necessary, install the Plate (02-150) in a Heating Unit at 150 °C (320 °F) for 1 h.

(d)
If necessary, lightly apply grease AEROSHELL 7 (M26C) to the special tool 09P1231.

(e)
Remove the  Lip Seal (02-070) and the Roller Bearing (02-060) with the special tool 09P1231 and a Hydraulic Press (Ref. to Fig. 6002).

Subtask 21-53-12-350-004-A01
(2)  Installation
(a) Installation of the Roller Bearing and Lip Seal
1

Install the Plate (02-150) in a Heating Unit at 150 °C (320 °F) for 1 h. 2
Lightly apply grease AEROSHELL 7 (M26C) to the Lip Seal (02-070) (at outer diameter).
Page 6010
3 Set the Plate (02-150) on the special tool 09P1524 (Ref. to Fig. 6002).
4 Set the Lip Seal (02-070) on the special tools 09P1180, 09P1181A and 09P1181B.
5 Carefully install the Lip Seal (02-070) in the Plate (02-150) with a Hydraulic Press set

to 200 daN (449 lbf). 6 Make sure that the Lip Seal (02-070) is fully in contact with the Plate (02-150). 7 Remove the special tools. 8 Lightly apply grease AEROSHELL 7 (M26C) to the Roller Bearing (02-060) (at outer
diameter). 9 Set the Roller Bearing (02-060) on the special tools 09P1180, 09P1181A and 09P1181B. 10 Carefully install the Roller Bearing (02-060) in the Plate (02-150) with a Hydraulic
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(29)