with the Figure (Ref. to Fig. 6002 Sheet 3 of 5).
(c)
Installation of ball bearings
1 Install the Ball Bearings (02-080), (02-090), (02-100) and if applicable (02-100) and (02-110) with a Manual Press at ambient temperature.
2 If necessary for installation, lightly apply grease AEROSHELL 7 (M26C) to the Ball Bearings (02-080), (02-100) and if applicable (02-100) and (02-110) (at outer diameter).
3 Apply grease AEROSHELL 7 (M26C) to the Ball Bearing (02-090).
Page 6011
21-53-12 JUN 15/10
09P1231
Plate (02-150)
Lip Seal (02-070)
Roller Bearing (02-060)
ACTUATOR- REMOVAL OF THE LIP SEAL (02-070) AND OF THE ROLLER BEARING (02-060)
(Sheet 1 of 5)
Figure 6002/GRAPHIC 21-53-12-991-016-A01
Page 6012
09P1181A
09P1180
Lip Seal (02-070)
Plate (02-150)
ACTUATOR- INSTALLATION OF THE LIP SEAL (02-070) (Sheet 2 of 5)
Figure 6002/GRAPHIC 21-53-12-991-016-A01
Page 6013
21-53-12 JUN 15/10
09P1181B
09P1181A
09P1180
Roller Beraing (02-060)
Plate (02-150)
ACTUATOR- INSTALLATION OF THE ROLLER BEARING (02-060) (Sheet 3 of 5)
Figure 6002/GRAPHIC 21-53-12-991-016-A01
Page 6014
(0.1102 to 0.1260)
ACTUATOR- PINS, BEARINGS AND LIP SEAL LOCATION ON PLATE (02-150A) (Sheet 4 of 5)
Figure 6002/GRAPHIC 21-53-12-991-016-A01
Page 6015
21-53-12 JUN 15/10
02-100 02-110 02-100 02-090 02-080
ACTUATOR- PINS, BEARINGS AND LIP SEAL LOCATION ON PLATE (02-150B) (Sheet 5 of 5)
Figure 6002/GRAPHIC 21-53-12-991-016-A01
Page 6016
TASK 21-53-12-300-803-A01
3. REPAIR 03 - ACTUATOR - REPLACEMENT OF MOTOR PARTS
A. Reason For The Job
(1) Use this procedure when it becomes necessary to replace the motor ball bearings.
B. Job Set-Up Information
(1)
Tools, Features and Equipment
Not Applicable
(2)
Consumable Material
(a) Equivalent alternatives may be used for the listed items.
(3)
Referenced Information
REFERENCE NAME
95° ETHYL ALCOHOL Cleaning fluid
(M26C) AEROSHELL 7 Grease
REFERENCE PAGE BLOCK DESIGNATION
(refer to Page Block 10001) 10001 ILLUSTRATED PARTS LIST
C. Job Set-Up Not Applicable
D. Procedures NOTE: CLEAN ALL METALLIC SURFACES WITH 95° ETHYL ALCOHOL CLEANING FLUID BEFORE INSTALLATION. NOTE: THE NUMBERS IN PARENTHESIS AFTER THE COMPONENT DESCRIPTION ARE
THE FIGURE AND THE ITEM NUMBERS OF THE IPL (refer to Page Block 10001).
Subtask 21-53-12-350-005-A01
(1) Removal
(a) Carefully tap the Rotor (04-150) or (05-160) to extract the Ball Bearing (04-210) or (05-220).
Page 6017
21-53-12 JUN 15/10
(b)
If necessary, remove the Ring Retaining (04-130) or the Screws (05-140) with the Flange (05-130).
(c)
Carefully tap the Brake Frame (04-100) or (05-100) to extract the Ball Bearing (04-140) or (05-150).
Subtask 21-53-12-350-006-A01
(2) Installation
(a) Installation of the Ball Bearing (04-210) or (05-220)
1 If necessary for installation, lightly apply grease (M26C) AEROSHELL 7 to the Ball Bearing (04-210) or (05-220) (at inner and outer diameters).
2 Move the Ball Bearing (04-210) or (05-220) on the Rotor (04-150) or (05-160) with a manual press at ambient temperature.
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：LIEBHERR-AEROSPACE TOULOUSE SAS COMPONENT MAINTENANCE MANUAL(30)
