S 494-043
(25)
If you tighten the cables again, make sure the fit of the rig pins has not changed.
S 414-044
(26)
Install the summing mechanism cover.
S 094-045
(27)
With the steering collar for the nose wheels in the center, remove the towing lever lockpin.
S 864-046
(28)
Make sure the towing lever moves to the NORMAL position.
WARNING:_______ MAKE SURE THE NOSE WHEELS ARE IN THE CENTER POSITION BEFORE YOU
REMOVE THE TOWING LEVER LOCKPIN. THE MECHANISM MOVES QUICKLY
AND CAN CAUSE INJURY TO PERSONS OR DAMAGE TO EQUIPMENT.
32-51-05
ALL ú ú 02 Page 410 ú Sep 20/90
A
757 MAINTENANCE MANUAL
RUDDER PEDAL STEERING INTERCONNECT - INSPECTION/CHECK
_____________________________________________________
1. General_______
A. This procedure only has illustrations and wear limit tables which show the data for wear limits. There are no procedures for access, removal, or installation of the parts. Refer to the Rudder Pedal Steering Interconnect - Removal/Installation for procedures to do these tasks.
TASK 32-51-05-206-001
2. Wear Limits for the Interconnect of Rudder Pedal Steering (Fig. 601)_________________________________________________________
A. General
(1) This procedure only has illustrations and wear limit tables which show the data for wear limits. There are no procedures for access, removal, or installation of the parts. Refer to the Rudder Pedal Steering Interconnect - Removal/Installation for procedures to do these tasks.
32-51-05
ALL ú ú 01 Page 601 ú Jan 28/01
A
757
MAINTENANCE MANUAL
SEE A
A
QUADRANT INTERCONNECT FWD
INBD
A
B
B
A Rudder Pedal Steering Interconnect Wear Limits Figure 601 (Sheet 1)
32-51-05
ALL ú ú 02 Page 602 ú Mar 20/90
A
757
MAINTENANCE MANUAL
13. SPACER/BOLT
B-B C-C
Rudder Pedal Steering Interconnect Wear Limits
Figure 601 (Sheet 2)
32-51-05
ALL ú ú 01 Page 603 ú Jun 20/89
A
757
MAINTENANCE MANUAL
NO. INDEX PART NAME DIM. DESIGN LIMITS WEAR LIMITS WORN PART REPLACE PART WORN REPAIR INSTR. REPAIR
DIAMETER ALLOWED DIM. WEAR MAX ANCE CLEAR-DIAM
MIN MAX
1 BEARING ID 0.4995 0.5000 0.5015 0.0020 X
SHAFT OD 0.4990 0.4995 0.4975 X 1
2 DRUM ID 1.1238 1.1243 1.1245 0.0000 X
BEARING OD 1.1245 1.1250 1.1238 X
3 QUADRANT ID 1.1238 1.1243 1.1245 0.0000 X 1
BEARING OD 1.1245 1.1250 1.1238 X
4 STEERING CRANK ID 1.1238 1.1243 1.1245 0.0000 X 1
BEARING OD 1.1245 1.1250 1.1238 X
5 BEARING ID 2.3115 2.3135 2.3175 0.0060 X
DRUM OD 2.3105 2.3115 2.3055 X
6 ECCENTRIC ARM ID 2.8750 2.8760 2.8800 0.0050 X 1
BEARING OD 2.8735 2.8750 2.8700 X
7 STEERING CRANK ID 0.2500 0.2540 0.2605 0.0110 X 1
BOLT OD 0.2485 0.2495 0.2390 X
8 ROD ASSY ID 0.2497 0.2500 0.2525 0.0030 X
BOLT OD 0.2485 0.2495 0.2467 X
9 BRACKET ID 0.2500 0.2540 0.2605 0.0110 X
BOLT OD 0.2485 0.2495 0.2390 X
10 CLUTCH ARM ID 0.4370 0.4420 0.4505 0.0150 X 1
SPACER OD 0.4345 0.4355 0.4270 X
11 BEARING ID 0.2495 0.2500 0.2525 0.0030 X
BOLT OD 0.2485 0.2495 0.2465 X
12 CLUTCH ARM ID 0.2500 0.2540 0.2605 0.0110 X 1
中國航空網(wǎng) www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機(jī)維護(hù)手冊 起落架 CHAPTER 32 - LANDING GEAR 3(124)
