sensors. 2) If the clearance is not in the limits, do the next step: a) Add or remove washers from between the head of the target and the surface it is attached to.
 NOTE: If more or less washers under the target does
____ not give the correct adjustment, you can add or remove washers from between the nut attached to the sensor and the bracket on the lock link.
 S 822-015
 (2)  
Do the steps that follow to adjust the landing gear up and locked sensor (Fig. 202):

 (a)  
Manually apply force to the uplock hook to put the hook in the locked position.

 (b)  
Make sure the clearance between the sensor and the target is within the limits shown on Fig. 202. 1) If the clearance is is in the limits, do the test of the

 sensors.
 

 32-61-02
 ALL  ú ú 01 Page 216 ú Dec 20/92
 
A

757
MAINTENANCE MANUAL

 2)  If the clearance is not in the limits, do the steps that follow: a) Manually apply a force to the uplock hook to release
 the lock on the hook. b) Remove the nut that holds the target into the flange. c) Add or remove washers below the target head to get the
 correct clearance. d) Install the nut and washer(s) on the target and tighten
 the nut. e) Manually apply a force to the uplock to lock the hook. f) Make sure the clearance between the sensor and the
 target is correct (Fig. 202). g) If the clearance is not correct, adjust the sensor clearance again. h) Manually apply a force to the uplock and release the lock on the hook.
 S 822-016
 (3)  Do the steps that follow to adjust the door closed sensor for the landing gear (Fig. 203):
 WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (a)  Open the doors for the landing gear and install door locks (AMM 32-00-15/201).
 NOTE: The doors for the nose and main landing gear open at
____
 the same time by ground release.

 (b)  Apply a thin layer of talcum powder to the surface of the sensor that gets an input from the target.
 CAUTION: DO NOT APPLY MORE THAN 1/8 INCH OF MODELING CLAY TO THE
_______ SURFACE OF THE TARGET. TOO MUCH CLAY WILL BEND THE SENSOR BRACKET WHEN THE DOORS FOR THE MAIN LANDING GEAR ARE CLOSED.
 (c)  Apply two strips of soft modeling clay that is 1/8-inch thick to the surface that gets an input from the the target. 1) Put one strip at each end of the surface. 2) Keep sufficient clearance to permit the clay to become
 larger.
 

 32-61-02
 ALL  ú ú 01 Page 217 ú Sep 28/01
 
A

757 MAINTENANCE MANUAL
 WARNING:_______OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (d)  
Remove the door locks from the main landing gear and close the doors.

 WARNING:_______OBEY THE INSTALLATION PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.

 (e)  
Open the doors for the main landing gear and install door locks (AMM 32-00-15/201).

 (f)  
Cut away part of each clay impression and make sure the clay has a thickness that is within the limits shown on Fig. 203).

 (g)  
Add or remove layers of the shim under the sensor to decrease or increase the clearance between the sensor and target.

 E.
Put the Airplane Back to Its Initial Condition

 S 092-027
 WARNING:_______OBEY THE REMOVAL PROCEDURE FOR THE DOOR LOCKS. THE DOORS OPEN AND CLOSE QUICKLY. THE MOVEMENT OF THE DOORS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
 (1)  
Remove the door locks and close the doors (AMM 32-00-15/201).

 (2)
Remove electrical power if it is not necessary (AMM 24-22-00/201).

 S 862-028
 

 32-61-02
 ALL  ú ú 01 Page 218 ú Sep 28/01
 
A

757 MAINTENANCE MANUAL
 NOSE GEAR PROXIMITY SENSORS - MAINTENANCE PRACTICES
___________________________________________________
 1.  General_______
 A.  This procedure contains five tasks for the proximity sensors for the nose landing gear. The first task is for the removal of the proximity sensor. The second task installs the proximity sensor. The third task adjusts the clearance between the sensor and target. The fourth task does a test of the proximity sensor. These first four tasks are for the proximity sensors that follow. The fifth task is an installation procedure for the nose gear target.
　
中國航空網 www.k6050.com
航空翻譯 www.aviation.cn
本文鏈接地址：757 AMM 飛機維護手冊 起落架 CHAPTER 32 - LANDING GEAR 3(164)